Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Hi,
I tried looking for an answer for this, however unsuccessfully. I have a custom characteristic and I set it with a string of values when it is added to the custom service...
Hi Everyone,
I'm having some trouble understanding the different combinations of low power modes and how to use them.
When I first power up my board I use about 500uA...
Hi team,
We are doing indoor navigation project using BLE nordic beacons and we are using ble_app_beacon as a transmitter.
We are calculating the position of person...
Hi there, i'm trying to connect to the internet from my nrf52 chip.
one way i think, we can use the ios as a shareing point for the embeded world.
And i tried from a win10...
Hello,
I have a Mesh application using the nRF5 Mesh SDK version 2.0.1.
I wish to implement the possibility for a node to forget its provisioning status and become unprovisioned...
Does the NRF51 DK come with a SWD interface connector-cable to plug into a PCB's SWD port when flashing/programming code into a WLCSP chip soldered onto the PCB? If not, are...
I'm trying to setup a simple host node to broadcast a attention message with no definitive destination node. I need any of the child nodes (primarily asleep) to see and process...
Hello everyone,
I tried to use the example project " ble_ant_app_hrm" SDKv14.2 but it doesn't work. The bluetooth connection work correctly, I connect my smartphone with...
Hello Nordic
I am developing our device. It uses SDK 14.2.0 and s332 SoftDevice.
This device communicate our app by using ble as peripherals.
I thought that our project...
Hi,
do the AES CCM module, AES ECB module, and the Cryptocell 310 (in nRF52840) employ measures against side channel attacks? I am mainly concerned with timing analysis...
Hi all,
I'm working with nRF52840 PDK and I'm using the last SDK and SoftDevice version: SDK v15.2.0 and SoftDevice v6.1.
I'm using the scanning module introduced in this...
hi
I am using nRF52832.i have added 3 service and and 3 characterastics to one service
1.Peripheral service (accelormeter + gyroscope sensor) and 3 characterstics
2...
Hi, Nordic team. I'm planning to create an iOS 11 BLE app.
I want to create a BLE app that can approximately depict indoor locations after the iOS device scans BLE beacons...
Hello,
I am thinking of using Thingy52 for my project. Before I order Thingy52, I would like to make sure if it will workout for my project.
(1) I wonder if data collected...
I am experimenting with light_switch server example from mesh SDK 2.1.1 . I want to add UART functionality to this example.
I referred to the ble_app_uart example from sdk15...
