Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Dear Nordic Team,
Thanks for supporting.
Still i am work with keil IDE. But now i want to go work with Segger embedded studio because of mesh concept. Please give me step...
I have combined light switch client and ble_app_uart example by following this guide and this case ,but after I added the codes :
#define MESH_SOC_OBSERVER_PRIO //<set...
Hi,
I am developing stuff for a bike and need the Bluetooth Cycling Power Service 0x1818
I found the 0x1816 Cycling Cadence and Speed
Has anybody developed this service...
Hello I'm a beginner and I try to use the DFU. I use the documentation and I can send my init packet without any problem. But when I try to send my Firmware I have 2 problems...
Hi,
Our system is based on the nrf52832 with SDK BLE_2.0.1 for the mesh. I have few queries as per below,
1)It would be great if you could suggest any vendor who is working...
When Going into Sleep, I see peaks of 12mA every 30ms (see image) I'm assuming I can adjust that changing the connection interval settings. I have my Connection intervals...
I'm having some issues with the freeRTOS example in SDK 15. I've always seemed to find a hardfault which limits the MTU size to 176. Now when I try and set the connection...
Hi,
I have a question regarding fast/slow advertising
I'd like to advertise for 180s using a 100ms interval, then switch to a 1s interval, preferably for ever. I set...
I would like to use ADXL335 accelerometer in this nrf52832 custom kit Hackable . I don't have a J-Link but i have this custom programmer Bumpy which is based on the Black...
Hi,
How can wake my nrf52832 based module from system off sleep mode. i am using ' nrf_pwr_mgmt_shutdown()' / ' sd_power_system_off (); 'function to put the device into...
softdevice 6.0.0 SDK15.0.0 How do I use ble_app_hrs sample code add buttonless_dfu function? I flow the steps, but I am fail. 1. In ble_app_hrs project... add nRF_DFU folder...
Hi Support team,
In this application note, solder paste type 4 has 25 to 45 micron particle size range while IPC J-STD-005 as attached stated type 4 has 80% Minimum between...
hi.
I used mergehex.exe to combine the hex of softdevice, bootloader, and application into one, but the board is in DFU state and the application does not start.
I am...
