I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Hello,
I've got a NRF52840-DK development kit and tried to configure it with a ATT MTU size of 512 bytes (larger than 247 bytes). I've activated data length extension and...
HI all,
I'm trying to get the Thingy Mesh Demo v0.1 working on my Thingy's. I am using the same SDK version as used in the demo ( Nordic nRF5 SDK for Mesh v1.0.1) and I...
I was able to follow the "quick start" guide for Mesh DFU and got things working with 3 nodes.
1 node (the serial host hooked to the PC) was programmed with:
bin/softdevice...
Hi to all,
i am developing a device with nrf51822 soc. i am using nrf51822 custom board, my board is https://pl.aliexpress.com/item/2V-3-3V-NRF51822-Bluetooth-4-0-Wireless...
Hi, everyone.
I am currently doing research for our new project - IoT alarm system for smart home.
One of requirements is Wi-Fi / BLE combo chip / module . Multi-protocol...
Hi all,
in Central mode I would like to retrieve the list of all the devices present.
I have developped a litle USB dongle, and I need to list alls peripherals, but after...
Hello,
I am using hardware PWM on NRF52832 in order to drive a MOS. I found something unexpected with the rates. i understand the PWM rate is determined by the clock divider...
So I'm trying to merge the ble_app_uart example with a project of my own, using SDK 14.2.0, but keep getting errors with the ram.
At first, my own project's ram start was...
NRF_LOG_ERROR should be coded not NRF_LOG_DEBUG for error conditions.
Not only will the log calls not be compiled and not displayed if
NRF_LOG_DEFAULT_LEVEL is less than...
Dear Madam/Sir,
I'm measuring the nRF52840 DK current consumption with my custom ble_peripheral app and other example ble_peripheral apps, namely ble_app_proximity, ble_app_pwr_profiling...
Hello,
I'm using the nRF51422 uController and the SDK 11. I tranferd from Keil to Eclipse and followed the tutorial to do so. But now I got a Problem while flashing my...
Hello Nordic team
I am working on "ble_app_uart_pca10056_s140" SDK V-15.2. IDE: Segger Embedded Studio.
After compiling above project I am trying to download two files...
nrf52840
sdk 15.2
i am using termite for serial viewer. and problem is my code gets complied with no errors and when i open termite there is no data in termite. i checked...
As it is stated in documentation, RTS is active low. But a peripheral device we use expects it to be active high. Can this be changed in software somehow or it requires a...
