Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
Hi All,
I have an issue with bootloader, in this i am successfully transferred application but after that my application not started.
i am just upgrading the sdk from...
Greetings,
I'm having the same weird issue as this question, though I don't understand the answer to it https://devzone.nordicsemi.com/f/nordic-q-a/34447/app-gets-stuck...
Hi everyone,
I've a nRF52810 based device that I am working with the Android based nRF Connect app on a Poco F1 (Oreo 8.1.0). The app scans the device properly but connection...
I just got my new nRF52840 dongle and went through the procedures stated. But I tried programming the nrf blinky firmware and after that I'm not able to connect the dongle...
Hi,
I am relatively new to the Nordic family of chips and I am very impressed with the level of documentation and support available, so many thanks for that.
I am working...
I would like to use the nRF52840 Dongle for evaluating the platform for a custom product. I need to make use of I2C, SPI, BLE and maybe 802.15.4 raw packet access. I'm new...
Hi :
I find some problem about th .
First I connect the USB,then I copy a folder with 18 binary files to my 52840DK,then reconnect.and compare the folders in DK with the...
Today, I tried out the Ble Bootloader from the Sdk examples.
As a central client, I'd used the »nRF Loader App« on an iPhone and also »nRF Mcp« on an Android Tablet (I'd...
I am interfacing My acc/gyro sensor (ICM-20648) with nrf52832. I am using my custom board and successfully get the mac address of my custom board. Noe i need to ensure about...
I use two PCA10040 for nus experiment, S132, SDK14.1
sniffer capture packets found that no data can be captured after the master send CONNECT_REQ, I guess it is not because...
Hello,
I have a working application on nrf52832, running sdk version 15.0 and SD132 version 6.0.0. Now I would like to add dfu functionality. I followed the instructions...
I followed this :
Connect the nRF5 boards to the USB ports and decide which one you want to use as a client and which one as a provisioner by noting down their 9-digit Segger...
Hi all,
I want to verify nRF52840 SoC SPIS peripheral on PCA10056 DK using any compatible SPI master hosts. I use SDK v15.2.0 SPIS example.
I know that Nordic SPIS peripheral...
