I've modified Nordic's "Nordic_Keyboard" sample to work with my custom board, just simple modifications to use custom_board.h rather than the default PC10028 configuration...
Hi,
I use HID application with S110 v8.0 profil.
I use BLE HID Keyboard example.
I put datas from smartphone to BOOT KEYBOARD OUTPUT REPORT and I whant read them by...
Hi all,
I use nRF51822 module and my environment is Eclipse + GCC + SDK 10.0. I refer to the example in path <SDK_PATH>/examples/ble_peripheral/ble_app_template, then make...
I am using nrf sniffer for trouble shooting. But it always exit unexpectedly. Wireshark was still open but the DOS window got closed.
I am attaching the log.txt.
log...
Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
I have been trying to use the nRF Connect app on my Apple iPhone in order to get the Current Time Service.
I bought a Arduino Primo that has an nRF52 on it.
The example...
I am working with an nRF51822 IC revision 2 chip and S110 SD 6.2.1 with Keil 5.10. My version of Keil 5.10 will not recognize the chip. I think that this is because I cannot...
Hi,
I am using nRF52832 microcontroller in project.
I use SPI interface for serial EEPROM.
I could able to see write packets are getting transmitted and verified the...
Hey, I use the Interactive mesh provisioning and configuration tutorial to setup one server and several clients which can communicate with this server.
Can you say me, how...
I have TIMER1 configured as 16-bits wide with no prescaler (62.5ns tick) and CC[2] set up for a varying value near 65535. My work is based on the Nordic blog post about synchronizing...
When I use uart to transfer data, sometimes I get error NRF_ERROR_SVC_HANDLER_MISSING in APP_UART_COMMUNICATION_ERROR when I start sending data. Sometimes this error occurs...
Hey, can I use a complex structure (for example byte array ) as a message parameter instead of one byte like it is done in http://infocenter.nordicsemi.com/index.jsp?topic...
I have a Thread network setup using nRF52840 as per the documentation below, using the Raspberry Pi image provided by Nordic. http://infocenter.nordicsemi.com/topic/com.nordic...
Hi,
In my develop environment , there have many proprietary device. One device is working on PTX mode, and the other devices is working in PRX mode.
If the PTX device...
Hi,
In the FICR (INFO.VARIANT) register on the nRF52832 soldered on my board I can read: AAB0 and in the same register on the NORDIC DK I can read AAE0.
The only different...
Hi,
as described here https://devzone.nordicsemi.com/f/nordic-q-a/37056/supervision-timeout-and-unplanned-disconnect our device has a hard current limit of 2mA.
Problem...
I have a trouble in my project.After flashing softdeivc,I flashed my application,but adversting is not work immediately, then a turn off the hardware and wait some second...
Hi:
I am developing my project based on ble_app_uart example. The development bench is SDK13.0, the chip is nRF52832.
One problem I have now is that: I configure Pin12...
When using FreeRTOS, external GPIOTE interrupts do not work.
And just how correctly to use the NFC with FreeRTOS?
In examples NFC use app_scheduler for events handling...
