Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
Hi,
I have a working application with Buttonless Secure DFU Service wich runs on nRF52832. I'm able to perform DFU without bonds, but I want to use bonding in my application...
Direct connection after disconnect I am using the iPhone 8, BLE device (51822/51422), s130, SDK 12.3.0.
and using a bonding and passkey to connect.
However, Direct connection...
Hi there
I met an error down below.
nrf_log_str_formatter.c(86): error: #29: expected an expression
if (RF_LOG_STR_FORMATTER_TIMESTAMP_FORMAT_ENABLED)
nrf_log_str_formatter...
Does the serial function operate with a soft device. Whenever i have an include statement for serial.h in a file with a softdevice I get a No such file or directory compilation...
I've been going off of the Buttonless DFU example to integrate DFU functionality into an existing project on a custom board. While I seem to have added the necessary includes...
I am programming a BL652 module (contains an nRF52832 with populated DC/DC inductors). I am programming it through the nRF52 DK in SEGGER studio.
When I run the blank (no...
Hi All,
A very general question here. I understand that using pre-defined services like the battery service help standardize the way peripherals send data to the central...
I'm using JLinkRTTViewer to look at RTT output from my code. The problem is that when I try to go into POWER_OFF, it generates a reset instead.
Is there a way to go into...
hi,
We want to position with aoa(angle of arrival) method, can it provide the One IQ-sample is a pair of in-phase and quadrature-phase samples, and Phase and amplitude information...
Hi,
I am using a nrf52840 development kit flashed with the ICMP example provided in SDK 15 and I am using a device with Bluez tools version 5.47 to connect to it.
However...
While investigating problems I'm experiencing with bootloader_secure I believe I've identified an error in the HCI TX finite state machine ( components/serialization/common...
We have implement a PPI for device match to trigger a GPIO toggle . but now we want to trigger a SW interrupt or a callback function .
my question is how to set PPI TASK...
Hi,
I merged UART exam ple from nrf5 sdk v14.2 with light switch client example from mesh sdk v1.0.1, i have 2 boards client board which is nrf52832 and server board which...
I'm developing an application using the NRF52832. Im using the ADC, and there may be times where the NRF52832 has 0V on its supply pin, but the voltage on the ADC pin is nonzero...
