This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
I'm trying to migrate to SDK15.0 (from 14.2) for the nRF52_DK and nRF25840_DK. Using the new nrfx_rng.c driver I'm getting a link error as a few functions can't be found:...
Hi,
I'm using nRF52840 with mesh 2.0.0 and started from the light switch example to build my own application. I have now 2 type of boards master (client+provisionner) and...
Dear Nordic Team,
Thanks for supporting.
currently i am working Single channel scanning with ble_app_uart_c example. In continuous scanning missing beacons. Please support...
Currently, in my application, any iPhone can attempt to read from one of my protected characteristics and initiate the bonding sequence. I have it set to "just works" mode...
Can anyone tell me if there is a specific problem on the nFR 51 using the 12.3 DK, where a disconnect is seen when it connects? I'm using Android Lolipop 5.0 on a BLU device...
Hi,
Im migrating from SDK8 to SDK12
app_timer crashes
Debugging at app_error.c shows m_error_data to be :
softdevice, pc 0x000104AE, fault ID 0x00000001 error_info...
Hello, trying to understand how to replace just the bootloader and s112 SD (app not installed), presently getting Insufficient resources.
First, mergehex -m softdevice.hex...
Hi,
Has anyone attempted to first transfer the entire image package to the external flash over BLE and then use a background DFU library to transfer from the external flash...
Hello,
I've got a NRF52840-DK development kit and tried to configure it with a ATT MTU size of 512 bytes (larger than 247 bytes). I've activated data length extension and...
HI all,
I'm trying to get the Thingy Mesh Demo v0.1 working on my Thingy's. I am using the same SDK version as used in the demo ( Nordic nRF5 SDK for Mesh v1.0.1) and I...
I was able to follow the "quick start" guide for Mesh DFU and got things working with 3 nodes.
1 node (the serial host hooked to the PC) was programmed with:
bin/softdevice...
Hi to all,
i am developing a device with nrf51822 soc. i am using nrf51822 custom board, my board is https://pl.aliexpress.com/item/2V-3-3V-NRF51822-Bluetooth-4-0-Wireless...
Hi, everyone.
I am currently doing research for our new project - IoT alarm system for smart home.
One of requirements is Wi-Fi / BLE combo chip / module . Multi-protocol...
Hi all,
in Central mode I would like to retrieve the list of all the devices present.
I have developped a litle USB dongle, and I need to list alls peripherals, but after...
Hello,
I am using hardware PWM on NRF52832 in order to drive a MOS. I found something unexpected with the rates. i understand the PWM rate is determined by the clock divider...
