I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
Hi,
I am trying to write my own dfu updater for the NRF51 chip and I am stuck trying to make sense of the actual DFU sequence described here infocenter.nordicsemi.com/index...
I am trying to set up mqtt between 2 nrf52s and rpi3 with the examples of sdk 15.0.2. I am very new to nrf52, rpi3 and networking. I have read everything needed as much as...
Let's send a string over UART. RTS signal will go low (active). So far, so good.
The problem is that RTS remains active even after sending is done. And because it is still...
I have two boards. I ran the exact same commands on both boards. The commands flash the same bootloader+app+softdevice+app settings hex file. One board reboots into the application...
Hello,
Setup: Running Ubuntu 18.04 inside Windows Host (using VMWare).
Device: nrf52840DK
Operating System (used for development): RIOT
I would like to communicate...
Hi,
I am running IoT LWM2m example. Everything were going fine since yesterday. when I do hcitool lescan, i see following output:
hcitool lescan LE Scan ... 28:45:8B...
I am using the ble_blinky example (s132) and want to increase the number of characteristics. I get the error code 4. I think the storage capacity is not the reason why I can...
Hi Team Nordic,
I started developing a project using SDK 15 using DK nrf52840 .
I went through several threads and started by creating a test folder inside example directory...
Hello,
I have the proximity example updating the battery service value fine using the provided nrf_drv_saadc.h driver. When converting the saadc driver to NRFX (nrfx_saadc...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi,
It seems to me that unused GPIO pins can stay float. However, earlier questions made me less confident.
Is firmware setting is enough?
Thanks,
Daniel
1. Is it reasonable easy to get a stable throughput over 1Mbps at a 3 meters range? 2. How much CPU resource is available at above situation? Or how many DMIPS is left at...
Hi
I am working with S130, sdk12.3 NRF51422_xxac
I have been successfully testing bootloader DFU example (secure_dfu_secure_dfu_ble_s130_pca10028) on the NRF51 dongle...
Hi,
I had tried the Thread Topology Monitor using nRF52840 PDK which was connected with PC via USB cable, and flashed it with Thread CLI example. But there was no serial...
