When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
I'm facing one issue while uploading firmware using BLE DFU.
Details:-
Hardware : NRF52840-DK
SDK : v15.0.0_a53641a
IDE : Segger Embedded Studio v3.40
Mobile App...
We have a Сustom BLE device and observe inconsistent behavior when connecting from this device to to nrf52dk running different SDK versions. - Custom Device connects OK with...
Hi All,
I'm trying to use the nrf52832 as the SPI master to get sensor reading through spi from another sensor. I want to base my firmware on the spi_pca10040 example but...
How can i sample nrf52 own input voltage to do battery measurements?My nrf52 chip is directly connected to a battery and it needs to sample its own input voltage without a...
I have been searching through the info center and can only find the slightest mention of the bsp_board functions.
Could someone help me, locate the right page documenting...
hi sir
i have start my project in NRF52-DK development kit but some BLE card give me data in three channel and i have received all data and give me same like data pls find...
I'm new to use nordic. I am using thingy 52. I would like to add a new custom feature that communicate text via BLE from app, store the text as userid in the thingy and check...
i use 52840, nRF5_SDK_15.0.0_a53641a\examples\peripheral\usbd_msc this example, and change the log level to debug
but i still can not see the DEBUG output information, this...
Hello.
I developing drone by nrf52832.
Developed based on nrf52-quadcopter .
physical web & drone is service uuid as below.
#define BLE_UUID_NUS_TX_CHARACTERISTIC...
Hello, I'd like to connect the nRF52840 to four I2C sensors. These sesnors may or may not have the same address and they will all be at the end of their own 2 meter long cables...
Recently, the side-channel attack "Screaming Channel" was described in a paper ( http://s3.eurecom.fr/tools/screaming_channels/ ).
The authors demonstrate a remote, passive...
Hello Nordic team
I am working on nRF52832 DK and SDKv-11. Can we increase MTU size to send more than 20 bytes in one packet? If yes then any example code do that?
Is...
i use SDK11.0 in 51822, I just need use BSP_BUTTON_1 interrupt, don't need BSP_BUTTON_0 interrupt, but i must initial BSP_BUTTON_0 interrupt, otherwise the current will be...
Recently, the side-channel attack "Screaming Channel" was described in a paper ( http://s3.eurecom.fr/tools/screaming_channels/ ). The authors demonstrate a remote, passive...
