Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
Hi,
I'm trying to capture Mesh packets using nRF Sniffer 2.0.0 and nRF52 DK while running the Light switch demo, but so far I haven't been able to capture any packet that...
Hi,
I'm having an issue when responding to rw_auth requests on the nrf52840 w/ sdk 15.0. When I'm attempting to update the table, If I make the length too large then it...
Good afternoon,
We just migrated our peripheral application, working perfectly on the nRF52840 DK, with SDK15.0.0 and SoftDevice6.0.0, and it is now crashing with SDK15...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
Hi,
I have tried the following example: infocenter.nordicsemi.com/index.jsp
Everything works fine (I can generate a notification via a calendar event and see it via the...
I get NRF_ERROR_INVALID_PARAM when calling sd_ble_gatts_characteristic_add(); If I comment custom service initialization where is this function I get the same error NRF_ERROR_INVALID_PARAM...
Hi, For a new project we need a smaller devices compared to to the nRF52832 dev board but still want to stay with the nRF52832 chip without making our own PCB. As an alternative...
We have a large number of units in the field running on SDK 13.0.0/S132 SD 4.0.3 and in order to add new functionality we need to migrate to SDK 14.2.0/S132 SD 5.0.0 via DFU...
Hi,
This is a follow up of issue: https://devzone.nordicsemi.com/f/nordic-q-a/28211/thread-dfu-upgrade-problems/111436
We're trying to perform DFU by following "Thread...
nRF52810 only supports S112 so the max throughtput anyone can achieve is 330 kbps .. please provide proof.. test data. Only nordic employee please answer this or someone who...
In SDK 15 the bootloader DFU enter check in nrf_bootloader.c has the following code:
if (NRF_BL_DFU_ENTER_METHOD_GPREGRET && (nrf_power_gpregret_get() & BOOTLOADER_DFU_START...
Hello,
We are working with Low Energy sensors that are programmed to make a periodic ADVs to our scanners/apps/Raspberries, in order to start a service if required. So the...
Hi,
I am using cli and made my own command like bellow, as you see i have a command with 3 sub commands. But i think my idea is primitive because if i have 1000 sub command...
