I've got some timing-issues with the nPM2100. As I could not locate the relevant information in the datasheet, I'm requesting this here.
My PCB has an nPM2100 with a mechanical...
Hello
I’m aware that this topic has been discussed in several posts from a couple of years ago, but I haven’t found a concrete solution yet.
I'm currently using an external...
When my peripheral calls sd_ble_gap_phy_update, setting rx_phys and tx_phys to BLE_GAP_PHY_AUTO, I receive the BLE_GAP_EVT_PHY_UPDATE event with a status of BLE_HCI_UNSUPPORTED_REMOTE_FEATURE...
Hi,
I recently checked support of MCUBoot validation and from NSIB for nrf54l15. (sdk 3.0.0 and above)
During this, I enabled Signature algo as ecdsa-p256.
And...
How to prevent storage partition from erase durning MCUBOOT firmware update?
I use Settings with NVS to store data
CONFIG_FLASH_MAP=y
CONFIG_FLASH=y
CONFIG_SETTINGS...
Hi,
I am building a Thread network ( www.youtube.com/watch with a Rasp Pi 4 as a border router, an nRF52840 DK as an RCP, and an nRF5340 DK as a child to be added into the...
Hi,
I would like to set up simple bootloader that initializes COMP module and waits for proper voltage on analog pin to show up, then launch BLE application.
Is there...
Hi,
I know that there is documentation, and that there are some answered questions abaut this, but still i dont think i understood how macro APP_TIMER_TICKS works. I need...
Hi,
I'm looking at adding IPv6 connectivity to my nRF52-equipped product. When I last looked a year ago, things seemed to be moving along very quickly. However, looking...
Hi,
I’m using nRF52840 with softdevice s140 and nRF5 SDK v13.0.0 and I’m having some issues regarding the optimization set up for the IAR Compiler (IAR Embedded Workbench...
Hi,
I'm using the "ble_app_multilink_central" example on my nRF52, what is the setting to advertise from my Android phone (using the nRF connect app) ?
Thank you
Hi!
I have some questions about the programing.
I want to do nRF24LU1 programing. I know I can do the programing by using USB port for the first time.
Do I have...
Hello,
I want to combine ble_app_gls and bootloader_secure project. Can you suggest me how to add dfu functionality to ble_app_gls project?
Thanks,
Shailav
image- publickey...
Hello,
What I want to do is to store custom data to flash using FDS in "disconnected" event.
When I try to write the data in "disconnected" event, the write_flag is...
Hi,
I have 52832(ble_app_multilink_central 12.2) which is connected to 5 51822 (experimental_ble_app_blinky) modules.
How to make 51822 not discoverable or not connectable...
Hi, I'm interested in the nRF5 SDK for AirFuel .
I have received a task to replace parts in a product which formerly used wireless charging and the CSR BLE chip.
I think...
If anyone will ever have this error:
When using c++ and singleton the use of operator new is not possible.
I found the solution in this post: forum.arduino.cc/index.php...
Hello everyone,
Lately I have been struggling while trying to run "BLE Advertising, a beginner's tutorial". My hardware consists of NRF51822 and PCA1000 dongle. I use SDK_11...
I am working through the TWIS Slave and TWI Master mode drivers Example using SDK 12 with the nRF52832 PCA10040 board and having issues. I am using Minicom through the terminal...
I want to use the last page of codespace for storing a single 32 bit word of non volatile data. I am failing so far and I think I just don't understand the page numbering...
