I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Hello, Nordic Team, I'm embedded designer from Russia, discovered your amazing wireless MCU NRF52832. I looked through your SDK and peripheral drivers, and unfortunately found...
Thanks Stefan. The zip file making and updating steps work perfectly for me, if I follow your steps and make it from your stock pre-built "dfu_test_app_hrm_s132.hex". My question...
Hi!
I'm trying to configure my NRF8001 module with the help of nRFgo studio. I'm using Nordic UART over BTLE service template. The module can be discovered via nRF Master...
I'm trying to make a BLE device that actually pairs securely. I posted this question on StackOverflow but didn't get any answers - maybe someone here knows more. As far as...
I am using esb in SDK 11 and my understanding is that the radio causes interrupts that are forcing and cannot be disabled. These in turn causes software interrupt 10 to be...
I just tried compiling this for the BLE nano and it explodes to a 245K download (much too large for device). I've also tried including only the headers (DigitalOut and wait...
Hi,
I purchased Nordic new reference platform nRF51-DK(pca10028) and try to work for DFU OTA.
In my test, first of all program S110 V7.1.0 by nRFgoStudio and downloads bootloader...
Hi
In a bit of an over-enthousiastic mood, I bought 3 pieces of the nrf51822 beacon kit, and the, as this did not gave me download access to the NRF51 SDK, bought a nRF51...
Is there an example of using sd_ble_gattc_write() to do a long write?
I'm assuming I need to use BLE_GATT_OP_PREP_WRITE_REQ and
BLE_GATT_OP_EXEC_WRITE_REQ.
devzone...
Hello everyone,
I am using the Softdevice s110_nrf51822_7.1.0_softdevice.hex and the dfu_dual_bank_ble_pca10028 example with SDK 7.1. I am trying to achieve a Device Firmware...
I am using Android Studio and am developing a system with the nRF51822. I would like to use the available sample code - nRF Master Control Panel APK for Adroid - available...
I'm wondering about the best way to implement a bonding and also a non-bonding device. There are a lot of code parts in the SDK that show a way of implementing a BLE peripherial...
I see there have been some issues with TWI in early revs of silicon, but looking at SDK 6 I see the twi_master_hw uses the silicon hardware to read/write the I2C device, but...
Hi
Can I use Bluetooth software version 7.1 en SDK versie 6.0 with the nRF51xx C0 Nordic version?
Or do we need the G0 for that?
and what are the main differences?
...
Hello
Where can I find operating characteristics of pstorage_store and pstorage_update?
Actually, I observe that about 100 ms are needed to update 4 bytes data. For...
Hi All,
I have two application modules which will use the flash , 1) Bond manager 2) configuration file
I have register both modules with different parameter in the initialization...
keil 5.12 could install pack file. I'd like to install S130 0.9 to keil 5.12, but I did not find S130 0.9 pack file. Could I install S130 0.9 manually and could select the...
Hi....
we are having some issues while testing our profiles in ios app.when switch from application to dfu am calling "sd_ble_gatts_service_changed(m_conn_handle,0x01,0x4D...
I'm looking for a simple and inexpensive solution for tying the TX and RX pins to GND after burning the OTP in production. What have other people done? I'd like to avoid having...
