Hi,
Is it possible in BLE channel sounding in ncs 3.0.1 to get some information about the quality of the distance measurement for each method? We have three ways to get...
Hi,
my name is Nick De Leenheer, and i am finishing my thesis on indoor localisation with CHANNEL SOUNDING. i currently got these outputs in my venv using SERIAL: so i...
Hi,
I´m working on a Zigbee-based environment sensor. You can find all related files here: https://github.com/Kampi/BeeLight
Now I have the following scenario: the whole...
Does the nrf54l15 have a register to specify the boot area? Similar to the NRF_UICR->NRFFW of nrf52833.Or does the nrf54l15 have to boot from address 0x00000000?
Hello,
I've been going through the BLE fundamentals course and things are going well. I'm using the nRF5340DK board and SDK version 3.0.2
I've gotten to lesson 3, exercise...
Hi,
I am working on the channel sounding feature on the 54l15 and I want to perform it sequentially between 3 reflectors and one initiator. I realized that after I make...
Hi,
We're at a point in our project where we're working through some regulatory testing for ETSI/FCC certifications with our BLE dongle board (nRF52840 + nRF21540 FEM...
Hi
I have an application where I cannot use the FIFO buffers (HW or SW). Therefore I need an interrupt for each received byte. If I try to use the uart driver (nrf_drv_uart...
I'm trying to program my nrf52832 with an ST-LINK /V2. I can't get both the softdevice and my app on the chip.
Flashing each one seperately works fine but then when I flash...
Hello there,
I'm trying to flash my custom nrf52832 pcbs(untill I get my DKs in the tech tour with a reconfigured stm32 disco board's SWD port with keil uVision using the...
Hello.
This is my code to "wait until micro sd card is pluged".
while(1)
{
disk_state =disk_initialize(0);
if(disk_state==RES_OK)
{
NRF_LOG_INFO("Initialize...
Hello community,
I have a central device which I implemeted, it is running with SD 132 v 4 ("NRF_SD_BLE_API_VERSION=4")
) the chip is a NRF52832, I have some movement...
I have no idea how i can install this and use it.
I would like if any one can explain in detail.
Can you get picture how I can do it?
I am using ble_app_hrs_nfc_pairing...
Hi,
As of now i am using nRF52840 and SDK 14.0.0 and i can find only BLE examples and i wanted to work on bluetooth 5 where can i find examples?.
And i want IR generator...
Hi ,
I am not sure if it is the right place. I was looking for WiFi: 802.11 b/g/n 2.4 GHz support in Arduino UNO and stumble into Arduino primo, which is developed in cooperation...
Hi,
I would like to only connect certain routers in a network using whitelisting. At the moment I'm trying to set a dedicated MAC address to a router and then use this...
Hi,
I am trying to implement the DFU ANT Bootlaoader on my PCA100040 board. I have uploaded the softdevice S212 and the bootloader with nRFgo Studio. I have an ANT dongle...
Hi, I want to read the StaticPasskey from the Softdevice that was set before with:
uint8_t u8_ToBePassKey[];
/*
* Configure ToBePassKey in some way...
*/
m_static_pin_option...
Hi everyone,
I am developing a remote control using nRF52832 chip. My prototype is currently developed in PC10040 board. The IDE is Eclipse Oxygen, and the SDK is S132...
According to here , pstorage_init should not be initialized twice.It links to another thread and the documentation which says the same but does not mention downfalls of doing...
