Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
I tried to add ble_nus service to buttonless app (sdk 14).
Keil doen't raise any errors and compiled project, but app is not work actuall in NRF_LOG I can see these messages...
Hello,
I'm confused regarding the nRF82840 matching network found in the datasheet and dev kit. Is the Pi-filter composed of C3-L1-C4 the 50ohm matching network or should...
Hi,
I have a Rigado BDM-300 (nRF52832) on a small custom board.
Using SDK 13.1 with SD132 v4.0.2.
I've taken a template project and adjusted it to my needs. I can get...
Not sure if there is already a worked-out example of converting analog to digital data from AIN0 and then updating a characteristic with that data.
I've worked through...
Hello ,
I am using examples\ble_central\ble_app_uart_c\pca10031\s120 in the SDK 10.00 .
I know that s120 supports up to 8 peripherals. I am using NRF51 Dongle as a Central...
hello everyone:
i use nrf51822QFAC(with 256kb flash and 32kb ram).The project is this "SDK12.3-ANCS\examples\ble_peripheral\ble_app_ancs_c\pca10028\s130\arm5_no_packs"...
Hi all,
I have a board with old code, it has a bootloader + sofdevice 110 + application all from SDK7 and I want to upgrade it via serial single bank DFU, to the SDK11...
I've developed a PCB containing the nRF51822. I am trying to uploaded the example program "ble_app_uart_s110_pca10028" to it, but the chip is not broadcasting (so I assume...
I use buttonless_dfu app from sdk 14
Generate settings file by nrfutil
Merge with bootloader hex file
Erase chip, flash SD, flash bootloader (everything use nrfutil...
Hi,
I am using SDK 12.2.0 with secure DFU service.i want to use pwm in my code.And i init pwm with APP_PWM_INSTANCE(PWM1,1),then i get an error:identifier "TIMER0_ENABLED...
I have built a custom board that is identical in schematic to the nRF52 DK board, with some additional circuitry connected as a SPI interface to the nRF chip. The MCU is the...
Hi,
Glad to see Nordic just released a new alpha version SDK yesterday!
I am wondering when you will release the mesh friend nodes support SDK? I mean support those low...
Hi,
I need you suggestion / information about Nordic chip. We currently have nRF52 (nRF52832) chip. However, in our application we will be using Nordic beacons as an transmitter...
Hello All,
I've finally managed to get Eclipse up and running after migrating from Keil, but now I'm having the following problem: I'm trying to port the buttonless_dfu...
