Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
To start off here, I'm using a Laird DVK-BL652-1.0, which according to Laird only needs to be re-configured to use the internal oscillator, but is otherwise very similar to...
Folks,
Have been using Keil MDK Lite in the past, in a Win VM. Larger code (over 32KB) plus the convenience of running without a VM layer have led me to switch to NetBeans...
Hi,
I want to use the AES-CCM of nRF52832. But it can not work with the softdivice.
I have read the following question and answer.
devzone.nordicsemi.com/.../
It seems...
Hi Nordic folks,
We are developing a product using nRF52832 with a Power Amplifier (RFX2401C) for extended range. For communication we are using ESB with some modifications...
I was redefining the init packet and when it came time to generate the nano-pb files, it looks like there is a fair amount of difference in the newly auto generated pb.c and...
Sorry if these questions are discussed already. I'm a newbie to Bluetooth project. Let me explain in brief. I have a central and peripheral device. I am transmitting 10samples...
After quite a few difficulties getting Keilv5 to work with the included examples with no responses ( devzone.nordicsemi.com/.../) I decided to give Eclipse a shot.
This...
Good day All,
We are in the process off procuring a project using nRF52, and I need to find out some important things. Are there any costs in using any of the libraries...
I am using nrf52840 module(peripheral) for transmitting 10samples/10ms and central device as the same nrf52840 for receiving the samples. Although I receive the packets, there...
Hello,
I'm working on an application in which I have to dynamically switch between a TWI master peripheral and SPI master peripheral that use the same peripheral ID (our...
I have an NRF24LE1 transmitter using ESB. It is sending a static payload of 10 bytes every sec.
The other configurations on the transmitter are: RF channel:2, CRC: 1 byte...
Hi,
i'm wondering if there is any IC (for example nRF52832) that can reach a range up to 155 meters available within the Nordic semiconductor catalog ?
i know that the...
In nRF5 SDK 12.1.0 a bug was fixed in nrf_drv_wdt_init(). Watchdog timeout could not be larger than 131 seconds because of (x * 32768) multiplication before. This bug is again...
In the spec it says that the typical ramp up time is 140us (or 40us in fast mode). But there is no details on maximum or minimum. What is the true tolerance on this value...
We are building a simple project, let 51822 connect the mobile, once per second. We found that the Tx power of 51822 is getting weaker and weaker (view the voltage over a...
