Hello everyone!
I want to form an Openthread network with three Nordic nRF52840 cardboards. I would like to monitor the traffic using a sniffer, but i can't receive any...
We are using the development board PCA10040 for implementing a prototype with several GPIO interruptions.
We are trying to use the NFC pins (pin 9 and 10) as pins of GPIO...
Development Software:
nRF5 SDK for Mesh v3.1.0
SEGGER Embedded Studio for ARM v3.50
SoftDevice S140 v6.1.0
Computer Platform:
Windows 10 Professional
Hardware...
Dear,
software/hardware:
nrf52832 mesh sdk v3.1.0
Q1: when friend feature node code can get? now just is bin file.
Q2: mesh has just four feature devices, friend feature...
It seems the LTE-M / NB IoT isn't available Europe-wide yet, and roaming applies country-wise.
Can anybody share his/her experience of using the BLG840F?
thank you.
Hi,
I am trying to build a thread network using a border router nRF52840 with a Raspi3B+ and 2 others end-devices nRF52840 connected on a CPU Ubuntu 16.04 LTS.
I have...
Hi,
I have a nRF52 DK board and I am trying to build a BLE peripheral with both connectable advertisement (custom with my own name and service) and unconnectable advertisement...
Hi,
We are planning to build a Mobile application for IoT involving Bluetooth communication. We came across a few part numbers of Nordic for this. We would like to know...
I had purchased the Red Bear Labs "Micro" board to develop code using their MK20 USB Dongle and Arduino.
If I "hack" the programming cable to emulate the "Micro" daughter...
Hi ,
I have recently bought a nRF5232 PCA10040 development kit and i am trying to interface nRf52832 development kit(Master) with AS3955(slave) over twi. I tested the twi_scanner...
Hi all
I'm trying to build a generator based on NRF52832. Outpit signals are: 8MHz clock and two latches signals highly sinchronized with clock - RGB_LAT and TXT_LAT. For...
Hello,
I have a question on how to calculate the capacitance based on oscillator relaxation for NRF52. For example, in the Csense_drv example, when pin is touched by finger...
Hi,
I have a working scanner and manage to require timeslots with the below timings.
Interval 300ms, scan window 50ms, Timeslot length 10ms.
But when i try to...
Hi,
Trying to implement a simple Hardware UART in parrallel with Ble on a custom board with mdbt42 Raytac module. I have the following compilation error:
*** Using Compiler...
I was trying to integrate mesh network into the ble_uart. I am using softdevice v7.3 and sdk6 with nrf51822. I followed the instructions given in the github link text
....
Hi, I bought an Arduino PrimoCore card and I read that you need to buy the Alicepad card. I can not find it on the net. But was it put on the market? Thank you.
Hi,
I have added new UUID (Service and Characteristic) into the uuid_definitions.json but it's not used in the application.
To try I put a error into the json file and...
Initialization:
The softdevice is initialized as in the BLE UART example. The body of the ble_stack_init() function is identical to the BLE UART example.
SPI is initialized...
I have two supplier for provide me nrf52832's based modules.
So I tested it and both is ok. The distance used pcb antenna almost the same (about 80m).
If I use on external...
My application is built using the nRF52832 device.
The system must only be "active" between certain times (5am through to 9pm).
I am a newbie and have no idea how to set...
Hi,
what are the minimal required steps to get the zephyr HCI-UART on a PCA10040 working with Linux BlueZ?
The steps I have so far [My host is Ubuntu 17.04]:
Physically...
