Hi,everybody！
When i install master control panel 3.10.0.14, i can't find nrf.exe in " C:\Program Files\Nordic Semiconductor\Master Control Panel\3.10.0.14\nrf ". Only nrfutil...
Hi,
I've been using the nRF51 dev kit, and today it stopped mounting when I plug it in. It doesn't show up as MBED or BOOTLOADER.
I use both Mac OS X and Windows, though...
SDK_9.0.0
I was trying to implement 2 different UART connection parameters so I decide to use re-initialization.
My initial parameters included APP_UART_FLOW_CONTROL_LOW_POWER...
I'm trying to use the nrf8001 (and arduino) to send MIDI (musical note data) to Mac OSX. According to the Apple developer site the midi profile requires that the characteristic...
I have a custom made board that has an EFM32WG360F256 communicating to an nRF8001, verified that the ACI protocol works with repeated echos, however when I run the efm_ble_my_project_template...
Hi,
I have 3 nRF51 DK pca10028 v1.1.0
I compiled and run power profiling example and after that I cannot flash or connect to the devices (tested in all three of them)...
Hi Guys,
Thanks for your precious time and insight. Let me try to explain what we did,
We have developed a custom board
After assembling the board, we do a bare board...
Hi all,
can we configure systick on nrf52840 to genrate exception every 1msec.
Tried doing the same but not able to observe correct value.
These are my configuration...
Hi. I need high data transmission rate(>500 KBps) over a long range(about 1000 m). Can you suggest me the best device according to my req.
Thanks & Regards
Utpal
Hi,
I have configured systick for 1msec value with Ticks=64000. When I read the systick calibration register value, the value is 0xc0000000. This indicates the Tenms register...
Hi,
is it possible for the NRF52832 to have an external I2S MCK clock when being in master.
Because I am working with a DAC/amplfier which will play some sound files from...
Hello.
I'm newbie in nrf51 world so maybe my questions will be a bit stupid.
I bought few nrf51822 modules on Aliexpress. Photo: www.dropbox.com/.../77_1.jpg
I bought...
Hi,
When trying to install nrf5x Command line tools 8.4.0 (under windows xp), the setup program ends with an error (see nrf5x-cmdlinetools.log ).
It seems to do with...
I want to be able to read my i2c and program logic flow within the BLE application but when I try to set breakpoints it causes the cpu to do a hard reset. How can I capture...
I have an nRF51822-DK board and so far I could not properly grab from the examples a simple thing: is there any specific initialization needed when coding?
For example...
Hi All,
I'm currently developing a network where I would like to use nRF52 SoC. The nodes in the network must be able to extend to over 100 and must be able to multi-hop...
Hello,
I've taken the example from the SDK 12.0.0 for RAM retention. I've added additional NRF_LOG statements to check if the RAM retention is happening. I do not have...
Hi all,
In the Data sheet ,i saw it is a short cut register . It is available for all the peripherals with offset 0x200.
Can you share more information about it, like...
Hi
We are developing a board with nrf51822 and we are looking for the PCB design layout guideline.
We actually went throught the PCB design tutorial on the nordic developer...
I'm attempting to build the ANT+ examples within SDK 11 and am hitting an issue in compile:
C:/Compilers/nRF5_SDK_11.0.0_89a8197/components/ant/ant_stack_config/ant_stack_config...
