This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
I'd like to clock the nRF52840 at the same frequency as my converters. Is there any problem with using a somewhat different frequency than the 64 MHz (or 32mhZ) crystal? If...
Hello guys,
i randomly get twi error busy 17.
i have #define TWI_DEFAULT_CONFIG_IRQ_PRIORITY 7 in sdk_config.h and .interrupt_priority = APP_IRQ_PRIORITY_LOW in init function...
My setup is based on a jlink clone and yunjia module nrf51822 and nRF51_SDK_10.0.0_dc26b5e. I am following this tutorial successfully till the section Enable auto discovery...
Hi,
The following function/macro is missing in SDK 12.2.0 and 12.3.0 but existed in 12.1.0:
nrf_drv_saadc_gpio_to_ain
I am re-compiling "thingy" SDK and it happens...
I'm looking for an answer as to how to know the source files that I need to mention in the Makefile if I'm writing my program from scratch. Are there some bare essentials...
Hello,
I am writing here because I am trying to change some concrete values from a .hex file in order to vary some BLE and other values. I need this because I need to generate...
Hello,
I downloaded the nRF Blinky app (for Android) here :
github.com/.../Android-nRF-Blinky
I'm looking to modfy the code to have an auto connection. For this, I...
As far as I can tell, the application is set to invalid (settings.bank_0 = BANK_INVALID_APP) after the application has been successfully deleted ( devzone.nordicsemi.com/...
im trying to use nrf_drv_timer_t with timer0 but I get identifier "TIMER0_INSTANCE_INDEX" is undefined error. TIMER0_INSTANCE_INDEX is defined in nrf_drv_config but this file...
Hello,
is the nRF51822 able to function as repeater or range-extender, repeating BLE signals from explicit two BLE devices (with known addresses)?
I know there are specific...
Hi,
we are developing a custom board based on an NRF51822 and for security reasons are using whitelisting.
So far this worked well with different iOS and Android devices...
i try to modify the saadc exemple program by includding pwm , but after including header file in the application , source in driver, and includding target, i get error always...
Hi All, anyone aware of a module certified for BLE v4.2 protocol? It doesn't have to be built on the Nordic chip, I'm interested in any other one too. Many thanks!
Hello,
I am using PCA10028 and sdk12.2. My challenge is nrf51822 resets after it executes the code for the first time.
I am storing few values in flash. After that I am...
