Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
Hello,
I am testing the ble_app_hrs project on two eval boards, with s110 and s120. Everything works.
If I power-off the peripheral board (s110), it seems that the master...
Dear Nordic guy, I'm developing with nrf51822.
I have one question regarding flash write.
In ble connected state,I have some error to write some data to flash.
I want to...
Hi,
I just loaded the nRF8001 Arduino code on my board and used an iPhone 5 to read the data that was being advertised. I get the following response:
<CBCentralManager...
Dear Nordic guy,I'm developing with nrf51822.
I have one question regarding lfclk.
I use LFCLK SOURCE RC OSCILATOR of ble_stack_handler_init() at the application side.
...
Hi,
Is there any example application related to alert notification profile for android 4.3 devices?
I just need to understand the gattserver implementation for the alert...
Hello All,
Since yesterday I have been getting a problem where my project using the S110 softdevice enters a reset loop. This runs on a unmodified PCA10001 that plugs into...
Hi,
I need to design a board that connects various sensor to a smartphone using the Bluetooth 4.0.
I'm interested in the NRF51822 chip but i have some doubt about what is...
Hi, I'm very new to programming microcontroller, so please go easy on me. :(
Firstly, apology if my post sounded weird, this is because English is not my first language...
Hi all.
I am making a custom PCB with nRF51822 SoC. For my project I need to achieve long Proximity range around 350 Feet. Where my Board will communicate with iPhone....
I have a timer that sends BLE data to a central every 5 seconds. The timers starts immediately out of reset. Until I actually pair the devices, the nRF51822 outputs an error...
I have problem to debug when I use softdevice it frezzes. At the moment I debug the program part with out use of softdevice is there any other solution? It the same code with...
Hi all.
I am new in nRF BLE. I am planning to buy an nRF51822 Kit but little bit confused with choosing EK or DK. Actually my plan is after playing with the Native Kits...
I am currently designing a board using the nRF51822 chip and I would like to implement a soft power ON circuit using the low power comparator (LPCOMP).
I understand that...
Hello,
I'm using a code posted on this forum to read ADC input and fill an array with the ADC values but I always get values between 166 and 174, (even if I connect the ADC...
