My sensor is off-standard,so I have to use gpio to read and write my sensor.
Gpio IIC will take about 0.5ms to get data.
My app need send data every 7.5ms,it seems that...
Hi,
My android Proximity application fails on service discovery only for the very first time it connects with the devices(nrf51822 evaluation kit with sdk 5.2.0). Actually...
Has anyone converted the app note AN34 DTM Python script to C# or C/C++ ?
The Python DTM script is works OK with the setup specified in the app note AN34 figure 2, which...
Hi,
I have a serious problem, when I use uart of NRF51822 QFAAC0 to receive data from another MCU, I found that it will lost one bit at same position everytime. my SDK is...
Hi,
I just started to interface the lcd display with nrf51822 evaluation board. The display i'm using is, spi compatible, 18" tft (160x130) from tiny lcd. I took spi master...
Hi,
We are using the nRF905 device in an application where it needs to switch between auto-retransmitting and sending single packets, due to it communicating with several...
Hi, recently I have been experimenting with the channel sounding with range requestor sample on the nrf54l15dk. I have modified the reflector code to make it connect with...
I am having an issue with the nrfx_qdec driver in zephyr, I am trying to simply detect when the turn happens and the direction of the turn is. Most of the time this is triggered...
Hi,
Hope you are doing well.
I would like to use eSIM on nRF9151-DK board and an eSIM has been assembled in the board. However, eSIM is not detected.
According to...
Hi,
I am currently conducting measurements using channel sounding with my nRF54L15 boards. I am at the end of my master thesis, so there is not so much time left to really...
Hi
I am using an nRF54L15 and trying to use pins for I2C, but to do this I have to disable the NFC pins.
I did the following:
But that wasn't enough.
I noticed...
Hi team, After executing RRAMC.ERASE.ERASEALL with an external debugger, I was unable to access the CPU (board) after reset. To resolve this issue, I connected the nRF-programmer...
Hi,
The attached code is based on a sample code from NCS v2.9.1 and creates a LittleFS flash disk on external SPI NOR onboard nrf54L15DK. There is a mismatch in the code...
Dear Customer Support,
Wanted to open a case to follow up on this old one Case ID: 335484
I initially looked at the counter alarm under
https://github.com/zephyrproject...
Hello, I would like to ask if the latest SDK version supports power management on the FLPR core of the nRF54L15. According to this article, the power consumption is quite...
hello everyone I have implemented BLE, ADC, RTC, and UART. After that, my power consumption is around 1.31 mA. Can you suggest possible ways to reduce power consumption or...
Hello Nordic team, For the ( POC), I configured ADC channel 1 and interfaced a potentiometer to pin P1.14. The ADC was set up to read the potentiometer's raw value . As part...
Keep hitting my head on this inconvenient workflow.
Edit build config
Select target custom board
Build config
All OK
Edit config again
Target board has been...
I was doing some developement for a custom board on NCS v2.9.1 when i noticed some of the changes i was making in my prj.conf weren't being set in the application. My impression...
Hello Nordic Team,
I am reaching out to ask for some advice and/or guidance on how I may debug code that:
1. Is initialized and runs BEFORE main
2. Is part of the zephyr...
Hello,
we are developing a device which implements BLE hid keyboard. The code is based on the hid keyboard example in the NRF Connect SDK.
The example uses battery service...
