Hi there,
I am using an NRF54L15 custom board and am trying to set up a functionality using DPPI + PPIB. using a single in (1 event) and single out (1 task). I have two...
Hi,
I'm trying to get the debugger to work on my target board. I created the attached simple program to eliminate complexity.
The debugger starts, but it starts running...
Hi.
After 3 days I've finally got littleFS working on a custom nRF52840 board. I am using nRF connect SDK v2.9.0 which includes Zephyr v3.7.99 with some additional Nordic...
Hello, I am working with a nRF54L15 and using a TF-M build (cpuapp_ns). SDK and toolchain are currently v3.0.2. NRF_SECURTY is enabled (by default) and here's the relevant...
Hi,
I’m working on a Matter application using the nRF Connect SDK v2.9.2 . I’ve added the AirQuality cluster into my device with sub-sensors: CO₂, PM1, PM10, TVOC, and Temperature...
Hi Team,
Recently we did a network related testing for our CL5G modem (nrf9160) and observed a problem, in this test we used a nmap tool, this tool will search for open...
Steps to reproduce the problem
Create a new application based on the Matter Light Switch example of the SDK 3.0.2
In prj.conf set CONFIG_CHIP_FACTORY_DATA_BUILD=n
...
Very strange, I have lots of nRF52x experience, but this one has me stumped.
Successfully updated our custom board/application from nRF5_SDK_15.0.0 to latest as indicated...
Hi all, I apologise for this very basic question, but I don't understand how to add/enable RTT debugging to my code. I want to practice writing basic code for the NRF5 SDK...
Could you please advise me regarding BLE security?
For security purposes, UUID data shouldn't be included in the advertising data package?
If we don' t put UUID in the...
Hello
My custom board has only 1 button and I'm trying to detect 3 button clicks. The first click is waking up the device and the other 2 are configured as BSP_EVENT_KEY_0...
I have a setup similar to this
When the callback is executed, the execution will enter the inbuilt_key function and then the output will stop and the execution will halt...
I'm using v1.2.0 for the nrf project and I am fairly confident I am using modem firmware 1.1.1 (though I don't know how to verify that).
I'm basing my project on "cloud_client...
Hi,
I am evaluating the ble_app_hrs_pca10056_s140 project with nRF5SDK160098a08e2 Dev kit and nRF82540 dev board.
I have put a breakpoint in line:
*p_erase_bonds = ...
Goodmorning,
what is the maxium current output for SPI pins on the nRF24LU1? The datasheet say "IVDD External load current" of 2mA, is this refered to the internal regulator...
In the documentation of the nRF SDK for Mesh v4.1.0 is written: "The following figure demonstrates how the data packets flow between mesh nodes and their layers within the...
Hello
Beacon using timeslot API
I am trying to implementing a beacon functionality using your timeslot API.
The beacon shall run in parallel to the normal SoftDevice...
Hi all,
In our application we have a piconet master (acting as GATT client) and several piconet slaves (acting as GATT servers). We have only limited time on the channel...
Hello,
I've asked this question already at StackOverflow, and while I try Wireshark I wanted to see if someone has experienced the same issue and/or can provide further...
I can scan beacons with Scanner. and can use NUS (ble_periperall\ble_app_uart ) to get connect with device.
My goal is to combine both application Have NUS Service to connect...
As most developers using Nordic's SoftDevice quickly find out, halting the processor (e.g. hitting a break point) results in a fault and requires a reboot. This makes debugging...
we want to use nRF52833 as BLE5.1 AOA/DOA locator,here are some questions about to how to use it:
How many antennas are needed for direction finding/positioning? Is 6...
