Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
Hi there, I'm using nrfutil ( nrfutil version 6.0.1 ) to dfu via ble (dongle),
Mac (10.15.2), windows (10), linux (raspbian) have been tried out to update the firmware none...
I am using the '840 to construct a small network using the ESB stack. In this design, a master (dongle) transmits to each slave and receives an ACK w/payload response. The...
I changed the way to get the upgrade program in the bootloader program and wrote a function to write the accepted bin file to the bank0 area. However, I found that it took...
Hi,
I am using BMD300 rigado board having nrf52. In my application i am tracking the ADXL362 accelerometer's motion.For this, I am combining SPI, UART(for displaying data...
Good evening,
after a very long research I couldn't find any answer.
Is (and if, how) it possible to connect an Arduino (or ESP32) via SPI, I2C etc. with the nrf52840...
Hi,Nordic Team
I tried to set 0,1,2 modes respectively in GNSS option, and the test current is as the attachment .
0 1 2
/**@defgroup nrf_gnss_psm_modes Values indicating...
Hi,
I am using nRF52832 with s112 BLE stack and SDK v16.0. I am wondering what is the most proper way for the "idle_state_handle()" method in the main loop.
Currently...
Hello,
I need to have connection status at the application level (IOS).
I'm working with the example "light switch server proxy" where the heartbeat profile is working...
Hello, I modified the instance in usbd_hid_generic to simulate it as keyboard. I checked the code of NRF52840 on github about the keyboard. It USES the function app_usbd_hid_generic_in_report_set...
Hello,
I really like your products since nRF51 but I noticed the same experience issues every time.
I tried your nRF9160 DK with the new SDK and I’m very disappointed...
Hello,
I am using NFC example "NFC BLE pairing reference", I could not paired with mobile phone through NFC. My android phone has version 10. The first time it paired successfully...
In my BLE project at the scanning side I see that application gets held if I remove filters from scan_init API and calls nrf_ble_scan_connect_with_target. I am refering to...
Hello
I'm working on my ble central that is based on nRF52832 and it's connecting to nRF52832 peripheral setup with Enviromental sensing service[ 0x181A]
This is log from...