Hello,
We are working with Onomondo in integrating their software SIM. We have it working and sending and receiving data, but am having some issues figuring out what is...
Hi,
so, If I take the WiFi scan sample from the nrf/samples/wifi/scan folder, and flash it to my board, I can reliably see my created hotspots, no matter if they're 2.4GHz...
We have a product that needs to support two different customers with two different SIM. One of the SIM requires the following four extra lines in the prj.conf in order to...
Hello,
I tested how "Direct Test Mode" app interacts with "direct_test_mode" firmware from "nRF Connect SDK" v2.8.0 (nrf/samples/bluetooth/direct_test_mode) and it seems...
Hello,
I am trying to send and receive data from an external slave sensor using the NRF5340. For debugging purposes, I have connected the NRF5340 to my PC via UART.
...
Hi all
I’m having a horrible time trying to get an nRF7002EB Wi-Fi coprocessor working with a nRF52840 via QSPI interface in nRF Connect SDK 3.0.2 (Zephyr 4.0.99). I'm using...
Hi,
We have a hardware application that prevents us from using flow control to interface with external hardware. We require the NRF51822 to be able to buffer up to 256...
I have a working design on the nRF51822 Evaluation Kit, and I now need to port that into a module that sits on a custom board. Any recommendations for making this process...
Could someone can tell me what is the difference between BLE_ADVDATA_SHORT_NAME and BLE_ADVDATA_FULL_NAME? I tried BLE_ADVDATA_SHORT_NAME and BLE_ADVDATA_FULL_NAME
advertisement...
I am trying to figure out how interrupts are set up for say a sensor with an interrupt line which signals when new data is ready.
I am assuming you set up a GPIOTE somehow...
I have been looking at the NRF51822 for data logging sensor measurements from the ADC. Currently, I have run into some limitations with iOS and can only get approximately...
Hello,
Its me again.First of all I want to say thanks to HÅKON ALSETH, with his help I was able to work with hardware interrrupt. now I am facing another problem, I need...
want to FLASH upgrade FW in the nRF51822 though my application controller. Is C or C++ code available for this operation or can you deliver a protocol description how to setup...
Hello Everybody,
I am new to Nordic and Bluetooth. I see nrf51822a have BLE + Cortex MCU inbuilt and this suits best to my application.
I have some doubts regarding...
How do I use nRF51822DK without "nRFgo Starter Kit Motherboard"? I have read "nRF51822 Development Kit User Guide v1.2" and have no result how can I only use nRF51822DK hardware...
Dear All
i would like to use
nRF51822
nRF51422
i would like to use nordic product,
but so shame, too low basic knowledge for make program for embedded, edit library...
Hello,
I attached the schematic found in the manual for NRF8001, in the case of DC/DC converter enabled.
It shows that an external 32.768KHZ crystal is used, while in...
Hello, I have major problem trying to debug/run ble_app_hrs example. The thing is that when I enter debug mode the code is stuck here:
0x000001B4 4908 LDR r1,[pc,#32...
Based on nRF51822\Board\nrf6310\ble\ble_app_hids_mouse example,
Used hid consumer page function, like play/pause or volume+ or volume- ...etc function,
In nRF51822 device...
I can't seem to find the hex file to download into the PCA10000 in order to use it with the Master Control Panel. Where is this documented in the dev-kit documentation?
