I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi,
i have found similar posts on the forum but could not find the answer. Therefore,I think it is necessary to raise this question again.
problem: platform:nRF52832 and...
Hello there,
I have been testing on nfc-uart example of SDK 13.3.0. I am trying to pass the buffer of 258 bytes to pointer "p_pdu" and its size of 258 to "pdu_lenght". ...
We would like to have that all communications, programming, and supply related TPs and SBs should be kept for debug purposes. Otherwise, we would like to remove all unnecessary...
We're working with the NRF5340 PDK, and it's a pretty big library change from the old SDK. So far I've been unable to find out where to configure the bluetooth PHY and link...
Hi everyone,
The task is as follows. I set up data transfer using notification. I transmit ~ 83 kB in ~ 10 sec. The connection interval parameters are as follows:
The...
Hi Guys,
I flashed the ble_app_uart example available in nRF5_SDK_15.3.0_59ac345\examples\ble_peripheral\ble_app_uart\pca10056\s140\ses location to NRF52840 DK board. In...
Hello,
I have been trying to get RTT to work with the nRF52810 but trying to compile the examples leads (as usual) to errors because there are a load of libraries and files...
Here is my program：
#define EXIT_PIN 31
void EXIT_Init(void) {
nrf_gpio_cfg_input(EXIT_PIN,GPIO_PIN_CNF_PULL_Pullup);
NVIC_EnableIRQ(GPIOTE_IRQn); NRF_GPIOTE->CONFIG...
Hi,
Our project is 2D-3D mouse. we are using nordic "ble_hid_mouse" application with some required changes for our application.
SDK we are using is 15.3
ISSUES ...
Hai,
we are using nRF52832 and Nordic connect for our development and testing work
we are facing disconnection issue on android after ~3min so we changed the CONNECTION_MIN_INTERVAL...
Hello,
I tried to configure Ozone for aws_fota sample without any success. I loaded elf files but one is debuging mcu boot and the other never access to the main. Do someone...
I just get one NRF9160 DK(PCA10090 0.9.0) to test the default asset_tracker application with Basis Simcard in the Oslo area. The modem firmware is mfw_nrf9160_1.1.0.zip. I...
In order to implement the standard RSA-PKCS, raw data must be signed with the private key without performing a hash.
All the CRYS functions wants either a HASH as input...
I want to drive a WS2813 led strip using a NRF52810, as NRF52810 does not have I2S, is there any other way to drive the strips. Do you know if there is any library for doing...
