I'm trying to implement channel scanning in our nrf24lu1p based USB dongle.
I'm following the specs and basically loop though each channel ;
loop
stop listening
set...
Hi,
I am using the NRF8001 in UART mode and attempting to bond with my android device (Lollipop 5.0 Nexus 6).
i am using the nordic arduino sdk which is found here:...
Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Are there any issues of pairing a nRF52833 using OOB pairing with a IOS device? Is there a good example code I could start with?
Thank you very much.
All the best
P...
The system requirements: 50 identical nRF53-based devices (each with a sensor and an actuator), positioned within a 3x3 meter square should be connected to a single computer...
Edit : The code posted below works on the 96x96 3V(LS013B4DN04) variant of the display, I still have no idea why it doesn't work on LS044Q7DH01, but I'm guessing it doesnt...
Hello!
I have some devices with a custom built PCB on my desk, all of which have my own custom firmware on it.
Sadly the devices don't have access to the debug pins...
Hi Team,
May I know the functionality of the below mentioned signals:
MIPI RFFE interface pins: VIO, SCLK, SDATA. MAGPIO interface pins: MAGPIO0, MAGPIO1, MAGPIO2. ...
Hi,
I got a question on nRF52832 platform. When it is brand new (so without loading any of our FW) and powered through 3V3, it draws up to 4.6mA when powered. But we also...
Hello,
We have seen the below error,
NRF_ERROR_INVALID_ADDR If the EasyDMA is used and memory adress in not in RAM.
While trying to connect with an external sensor hub...
Timer A with a 10-minute interval, timer B with a 4-hour interval, and timer C with a 10-second interval are required, and A and B should also run out of time in low power...
Are there any updates on coded phy support for the nRF sniffer?
I found a thread about this from "over a year ago" which says to check back in 4-5 weeks: https://devzone...
When CENTRAL connects how can I read the UUID and ADDR of the peer?
static void ble_evt_handler(ble_evt_t const * p_ble_evt, void * p_context) {
switch (p_ble_evt->header...
Hi Team,
We are facing issue with Flash storage Handlers with ble handlers. When we add the fstorage to my application ble adversing is stopped suddenly.
We are having...
Hey,
I want to use a standard 16bit service and to add some custome characteristics to it, will this create any compliance issues? Is it complying to BLE specifications...
Hi all,
I'm using the "ble_beacon_app" example from the SDK 16.0.0 with the nRF52840 DK. I would like to change the TX power level.
In main.c function, I tried to change...
Hi All,
We tried to modify the Android source core of nRFTools for our Proximity application . And we used some nRF52832 and nRF52840 as the proximity device.
1) We connected...
Greetings,
we are developing a custom board that holds a nrf9160 chip. We have uart lines out on pins 28 and 29, as on the DK. We need to use the AT client in order to flash...
