We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Hello,
We are working through an issue which we found recently on the nrf sdk. The following is what is occuring:
We have two GPIO interrupts configured for low accuracy...
Hi... folks .. i am using nRF52840 development kit , i need to control the two servo motor using ble commands . I need to control the angle and speed of two motors , suggest...
Hello,
When I power our customer-designed nRF52832-based electronics I see the ingoing suply current (at 3.1V) rising in about 3 seconds up to 55 mA (!), then decreasing...
Hi, I have a problem with uart disable function (app_uart_close();). I started from ble_app_uart example, and I want to disable uart when nobody is connected to the Ble device...
Hi,
I have a similar problem to the case: ( devzone.nordicsemi.com/.../having-a-problem-with-preprocessor-options) with not being able to access the preprocessor options...
Hi,
As per the workaround of these errata its mentioned that "This code is already present in the latest sytem_nrf52.c file."
What does the latest mean here? Is there...
Hi,
I have two questions, one regarding nrfjprog and one regarding pynrfjprog:
How do I write content to a specific address of the flash using nrfjprog? Specifically...
I want to build custom commissioner app on nRF52840 DK. But when I'm running:
The error is OT_ERROR_ALREADY. I don't understand why, I am not invoking this method multiple...
I am using the nRF9160dk development board and I could not find a test or example for the internal RTC. could you provide a simple example of using the internal RTC.
Hy,
i get two warnings from my c++-compiler (arm-none-eabi-g++ (GNU Tools for Arm Embedded Processors 7-2017-q4-major) 7.2.1 20170904) if I use the header cmsis_gcc.h in...
Hello
in the thread about NUS connection problems with TimeSync example ported to SDK16.0.0 Sigurd confirms a bug in the timeslot API.
Could you please be more specific...
Hi,
I am using nRF52832, SDK16.0
with SES
Is that nRF52832 have able to send timestamp through BLE. is that hardware able to calculate timestamp
will it act as REAL...
HI
my Version: SDK15.3,ble_app_template,custom board with nrf52832
I'm trying to load device name from fds when initial,
my goal is sending message to my board to change...
For some reason, it seems that I am not able to send any raw data with the BLE radio. I am able to configure the radio and start it successfully. However, the radio never...
