Hello,
I want to perform some antenna measurements and compare the rf performance of my custom PCB with an nrf9160 SiP with the nrf9160 dk.
To perform some antenna measurements...
Hello - I have the exact same question as proposed in this thread - I am wondering if there has been any change in the 3 last years since it was posted.
In a nutshell, we...
Hi I want to build a multi role BLE device.
As a peripheral it shall stream ADC data with arounf 20 kbytes per second.
As Central it shall receive adv_nonconn_ind packets...
Dear Nordic Engineers
I developed a PWM function to drive the RGB LED. Then I found a problem, which is w hen I used a PWM signal of one channel to control the RED light...
I get error provisioning key on nRF54L15 and NCS 3.0.1. I tried using "Erase all" in nRF connect SDK Programmer, but it doesn't help. Please check also the attached log. nrf54l15dk...
Hi，
I am using nRF54L15-DK for Zigbee light_stwitch startup testing. After successfully connecting the development board to the Hub for the first time, I evaluated the time...
Hi
I have a code previously can be built in NCS 2.91:
However, when I use the new NCS 3.01, it can not be built, the error is:
Could you please help me figure out...
Hello,
I'm currently trying to integrate the Android-nRF-Mesh-Library in our App.
Identifying works fine but when the library tries to send the public keys to the node...
I am trying to set up FOTA support with external flash for mcuboot secondary partition. I have gone through several tickets on the subject, but haven't been able to solve...
I'm using the nRF9160 with the LIS2DH accelerometer and SDK version 2.5.2 . In my hardware setup, INT1 is connected to GPIO 0 and INT2 to GPIO 1 . I'm configuring both interrupt...
I am trying to use TTM (nRF Thread Topology Monitor package) with a newly bought nRF52840 Dongle (PCA10059) on Windows.
Following the instruction at https://docs.nordicsemi...
Hi ,
I am developing an application which uses nrf52833. I want to perform OTA using 4g module(from Quectel). As per my understanding and explorations, there can be two...
I'm developing code to run on the nRF5340 SoC in a Thingy:91 X and I am seeing duplicate RTT output. For example, if I look at the RTT output from the default 'Connectivity...
Hi, I recently noticed crashing in sd_clock_hfclk_is_running() on a nrf52840 using SoftDevice S140 7.3.0. This is the callstack:
??@0x00000ac4 (Unknown Source:0)
...
Hi,
I am currently using 54L15-DK to create a radio test example, but there is a problem when I build the project: - sdk version: v2.9.0 - toolchain version: v2.9.1
...
Hi everyone,
I use the ble-app-buttonless-dfu example to develop my application.
I make a mutual authentication to be sure the device is connected to the right mobile...
Hello Nordic community,
I’m working on a project with the nRF52840 DK (PCA10056) using the nRF5 SDK and the S140 SoftDevice. My goal is to:
1. Read two NTC thermistors...
Hello everyone,
We are developing products with nrf52840 and our default supply voltage is 1.8V.
Is it possible to program a custom 1.8V board with nRF52840DK?
We are...
I am trying to compile hci_lpuart for thingy91_nrf52840, but I have these issue. hci_lpuart:
Any ideas on how to solve this? I'd really appreciate it. And if you have any...
Hello, I've recently upgraded my pre-production application on nrf52832 from NCS v2.6.2 to Ncs v3.0.1 also upgraded to HWv2(on interim ncs 2.9.0 as adding custom board for...
Hi,
I am trying to install NCS v3.0.1 on Ubuntu 24.04 PC and I get the following error.
Looks like ZEPHYR_BASE is not setup. I am trying to follow the Fundamentals Course...
