I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi, i'm using two nrf52840 DK ev kit. One it's the central and one the peripheral
After the connection I need to save power at the peripheral board, because the cpnsumptio...
In mesh example project “dimming_server”，I have added functions: mesh serial, SAADC(use ppi) and compie pass.However,when debugging,an error is happened in the function"nrf_drv_timer_init...
We would like to reduce the attribute table size a little to increase free RAM. Are there any guidelines explaining how we can judge how large the table needs to be for a...
I compile SDK7.2 example hrs in "experimental_s110_with_dfu" by eclipse,
and I download softdevice & bootloader by nRFgo
then i use master control panel to DFU the hex which...
In the nordic documentation it mentioned that in the init packet we can write list of supported softdevices so that if one of that matches it will start the dfu. But in Signed...
Actually, I'm not good at using English. So I'll try to struggle to type this question...
Sorry, Last week. My boss gave me a Nordic Mouse to develop some embedded one...
Hello,
I am using nRF51822 and meet a question that in the process of bluetooth communication, I will get an instruction for external circuit to stop bluetooth function...
While both P0.00 and P0.01 has Analog Input function, initializing an AnalogIn (in mbed) with P0.00 will cause the firmware to fail to start at all; but initializing using...
Please tell me the Manufacture Part no: which is used for the 16MHz crystal in the PCA10040 DK. I found it different from the one used in PCA10028 version of the DK with just...
Please tell me the location to download the hardware files for pca10040 version of the nRF51 DK board. I could find only pca10028's hardware files in the nordic's webpage...
Hi,
I have some similar problem when trying to add the custom 128bit characteristic UUID.
The service UUID is advertised correctly but the characteristic UUID not.
...
Im using nrf51822 (16KB RAM), I'm trying to retain some data (RAM) after watchdog reset. when I load only the softdevice and my app, the RAM retention workings, but when I...
HI , ALL
i coded the uart_init in my project.
and i want to regarget the printf in my project.
so i find the retarget function is in the 'retarget.c' ,
i tried...
Hi,
We are using Softdevice S310 Version:3.0.0 and SDK:9.0.0.
My Device working on battery power. We are facing Flash write problem when my battery voltage goes to below...
Please tell me the safe 'Max Voltage Rating' for the capacitor at the DCC pin of the nrf51822 in DCDC mode. I am talking about the C12 cap in the circuit shown in Page 113...
Hi all,
I have an interesting problem where I want to read my bootloaders version (based on the DFU), which I have located at 0x3C100, from my application.
I confirmed...
