I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi, i'm using two nrf52840 DK ev kit. One it's the central and one the peripheral
After the connection I need to save power at the peripheral board, because the cpnsumptio...
In mesh example project “dimming_server”，I have added functions: mesh serial, SAADC(use ppi) and compie pass.However,when debugging,an error is happened in the function"nrf_drv_timer_init...
Hi everybody.
I am making an application using ANCS, I saw that the original ANCS application saves some data to flash memory via device manager module and the parameters...
Is there a way to get to an softdevice/radio event, which is generated every time an advertising packet is send? I need to set a pin in high state while sending a packet.
Hi,
In my application, I am using nus service with S110 V7.1.0 (nRF51822). I faced to one problem that the rx channel is set up to notify characteristic. In iOS (8.3),...
My question is while the application is running, how can I disable the NUS service to turn on the DFU service. This idea stems from this question: devzone.nordicsemi.com/...
I am using esb in SDK 11 and my understanding is that the radio causes interrupts that are forcing and cannot be disabled. These in turn causes software interrupt 10 to be...
I've testing a Raytac mdbt40 module and I'm running the ble uart example (sdk 9.0, gcc debug enabled, no gcc optimization) and no external 32khz crystal
I can scan and...
Hello,
i would like to update my SDK to SDK11, but i'm not sure that the pack installer in keil works..
What are the different versions of the pack?
I 've this one...
Hello All,
The compatibility matrix states that the sdk for rev 2 devices has been discontinued on version 6.1.
We have some other products with rev 3 devices where...
Hi!
I'm using nRF51DK with s110_nRF51_8.0.0 Soft Device and SDK_9.0.0.
My application reads ADC with frequency 500Hz (2 bytes of data from one sensor each read), and twi...
I am just wondering about the status of nrf52 support for the mbed platform (specifically as a yotta target).
I have seen a number of other threads on both the nordic side...
I am developing an application on a STM32 CPU that uses a 51822 through BLE serialization for BLE connectivity.
I have connected some LEDs at the pins of the 51822 to indicate...
Hi,
The nRF51WLCSP needs IR blocking coating and I found here that an example epoxy can be Epo-tek 320. I just want to check if there is any specific time for covering...
Hi
I have been able to successfully write using FDS but I'm unable to read back using the same keys. Here are my code snippets:
#define FILE_ID 0x1111
#define REC_START_ID...
Hello~
I'm using JLinkEXE to flash an nRF51822 chip. When I use nrfgo and press "erase all", it wroks. But after if I flash the s130, I can't erase the s130 with command...
