I am testing out the nRF54H20 on the nRF54H20-DK version 0.9.1. I have followed the steps for setup in the "Getting started with the nRF54H20 DK". I currently have nrf54h20_soc_binaries_v0...
I am trying to get a WiFi project working using the nRF52840DK and nRF7002EK . I use a 3.3V power source that is supplying power to both nRF's in parallel. For the nRF7002EK...
Hi,
I'm developing firmware for the nRF52840 DK using nRF Connect SDK v2.9.2 , and I’m running into a problem that didn’t occur in v2.8.0 .
My project uses Zephyr and...
I'm trying to run the DFU sample l9_e5_sol on a custom board using the nRF5340 and SDK version 3.0.2.
My goal is to perform DFU over BLE using external flash. However, before...
I am receiving an error when connecting to a custom board by running nrfjprog --reset, any similarly with any other commands that require connection.
I am connecting through...
I am receiving an error when connecting to a custom board by running nrfjprog --reset, any similarly with any other commands that require connection.
I am connecting through...
We have previously used nRF52840 and for the latest iteration of our board design we are updating to use nRF54L15.
We are aware that for nRF52840 we could map any pin to...
i m using pca10028.. with gcc tool chain setup with sdk 8 in windows.....am run one ble_uart example and after 180 second my device goes to sleep.. and second one that i have...
I'm using the SAADC of an nRF52832. I'd like to reduce the error of my measurements from the nominal +/-3%. I'm calling the NRF_SAADC_TASK_CALIBRATEOFFSET periodically to...
Hi,
I am trying to use nrfutil to generate my verification key.
However in the bootloader the key has this format
__ALIGN(4) const uint8_t pk[64] =
{
0x6e, 0x76...
Hello,
I am trying to update my bootloader using DFU and I am running into a few issues. I have successfully flashed and tested my current bootloader on my board and everything...
I am using the nRF51822 in an application where I want to run the UART as fast as possible to communicate with a host processor. I have been able to get reliable communication...
I am trying to create a package file to use with the DFU on my design.
I followed the instructions for getting nrfutil latest version built and was able to generate a private...
I'm using an NRF8001 with an ATMEL ATMEGA 328P (the microcontroller from an Arduino). I need the microcontroller to go to sleep, but still allow the BLE chip to advertise...
Hi,
for development i am using gcc and makefile on osx.
I wanted to automate my makefile with the possibility to upload directly the hex file to my nrf52 devboard.
...
I'm using PPI to trigger a gpio high after a given delay from 4.00 ms to 8.00 ms. I need to be accurate up to .01 ms but i'm seeing some jitter in the actual delay vs given...
Hi,
documentation for NRF_LOG_RAW_INFO state that it is:
A macro for logging a formatted string without any prefix or timestamp.
But when I use next code snippet...
Hi
After building ble_app_uart in Nordic SDK with board pca10028 it gives some warning like
/usr/lib/gcc/arm-none-eabi/4.9.3/../../../arm-none-eabi/bin/ld: warning...
hello sir, i m using gcc tool chain setup in windows with sdk12 in pca10028... so can i useexample->peripharal-> timer example same as rtc ... i mean sleep condition same...
I would like to use the flashwrite function to store some data in the flash. There is an example in SDK 11.0/peripheral.
But I have a few questions about the example: ...
Hi
I need to develop PC software to Discover, Connect, Get and Set data to the nrf device that we developed.
I am using the MCP and nrf connect but my client want to...