Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
just when I send command to nrf51 to stop advertising by calling sd_ble_gap_adv_stop I got error NRF_ERROR_INVALID_STATE . what's the source of this error ?
static void...
In the past nRFGo Studio worked fine. Then I reinstalled windows due to an unrelated problem (and changed from 32 bit to 64 bit), and now it reliable freezes.
Most often...
To have a reference receiver to evaluate a new antenna design i would like to use the nRF52 development kit.
Therefore i am looking for a example application that can be...
Hi,all,
in the Core 4.2, the sentence with word 'Controller' and 'Host' have appeared many times.
like 'When a Host performs the auto connection establishment procedure...
Hello,
I'm using a custom board (nRF51822 QFACA chip), with the optional 32KHz crystal.
When, I use the SDK 5.1.0 and the S120, my code works perfectly. But when I try...
I would like to develop some BLE applications using the nRF52 Preview DK, that embed a NRF52 revision AA. S132 soft device 2.0.0-8.alpha documentation says that is not compatible...
I've been developing some ble code for a custom board. Recently, I just finished creating a new smaller board. When I load my code onto it, I notice that I have trouble discovering...
Can the nRF52 be programmed by 6-pin J-Link Adapter by just connecting the following 4 pins,
Pin 1 : 3.3v Supply,
Pin 2 SWDIO,
Pin 4 SWDCLK,
Pin 5 GND,
Can pins 3...
I want to save custom data in NV address. Which address is safe to save custom data in NV?
I'm working on nRF51822-xxAC with very simple and small code.
And, using s110...
My project for nRFs has a few configurations for different boards.
So, how to enable 'batch build' button to build all configurations by one click? Currently this in disabled...
code.c
ui_flash.c
ui_flash.h
Hi guys,
So we are building the Ibeacon project , and faced with some problem:
The chips falls hard reset periodically when trying...
Hello,
Is there any todo list about how to protect an application from hacker unsollicited copies to avoid illegal clones ?
how to allow jtag in write only (disable...
Hi all,
For PAN 42 which describes an issue write to RAM after a POR. When was this issue fixed? I can't seem to find out what versions of Silicon are subject to this issue...
Hi, i try to understand how to use power down modes. But i have a problem in the example ( nRF24LE1 REGISTER RETENTION TIMER ON ).
while(1)
{
// Register retention mode...
