hi support team,
when i testing wifi location, i found out one problem:
nrf_cloud_rest: Failed to encode location request, err: -12
that is this code in nrf_cloud_rest...
https://academy.nordicsemi.com/courses/nrf-connect-sdk-intermediate/lessons/lesson-9-bootloaders-and-dfu-fota/topic/exercise-3-dfu-with-external-flash/
I have this exercise...
Hi,
I noticed in the nRF54L QFN48 reference design, for the NRESET pin, there is an RC filter (1Kohm series R and 3.9pF shunt cap). What's this for and is it necessary?...
Hello,
I am using a nrf5340 dev kit. When I use SPIM the output from the pins gives the correct hex values but the output's amplitude is only around 100-200 mV. I know that...
Hi,
I'm using the nRF52840 with the SoftDevice for BLE. In my system, it's primarily a BLE transceiver controlled via SPI by an external TI MSP430. We're considering implementing...
Hi,
We are having issues with this part bridging on our via-in-pads. We are using 2oz finished outer layer copper.
Do you have any footprint recommendations for 2oz copper...
Hello,
I'm looking for guidance and understanding of how to properly use the KMU and ITS for secure key storage of a key generated on device.
I see that typical ITS use...
I have nRF8001-DK and Arduino Uno. ble_uart_project_template from nRF8001 SDK for Arduino (Bluetooth_low_energy_for_Arduino_0_5_0_0_RC2) was used. It was used with Master...
Hello,
i create a custom profile with two services and with 30 characteristics. The first service has 29 characteristics. Up to this point everything is ok, but when I...
Hello, i would like to know if its possible to use your SDK tools (S110 Soft Device, nRF51 SDK) without your evaluation/development kit.
Since RFduino has a RF51822 chip...
Hi, I try to create a iBeacon tag with NRF51822 for Apple device, but it seems not to work, yesterday I update the newest SDK, I found the ANCS was added, so Nordic also can...
Hi,
i have a big Problem, if i debug my code i get in some cases in register 3 the value 0xDEADBEEF and after that the device doesn't work any longer in a correct way....
Hi
I can use the duf_dual_bank_ble to do the OTA,but I donn't know how to use the dfu_single_bank_hci to do the OTA.Could you give me some
advice about it?Thanks.
Hi.
I have a problem with writing value to gatts attribute when device is in connection mode. In my application I want to check if the parameter writing by the client to...
Hi,
I have downloaded the new version of SDK (v.5.0) today and just tried your experimental ble_app_ancs (no modifications) but it seems it asserts with error_code=0xB...
Hi,
I need to know when to use the write_wo_resp property for a characteristics, and what is the difference between write and write_wo_resp property of a characteristics...
I've read a post from Marc Nicholas about the attempt to port the entire gcc toolchain under Xcode on Mac OS X.
As I wrote in another post, I've the entire gcc toolchain...
I'm getting started with this evaluation kit by working through the user guide and almost made it through the Blinky example before I ran into trouble.
After compiling...
We have some hardware versions of the Nrf51822: build BA, CA.
Is the new S110 v6.0.0 softdevice compatible with these hardware versions?
If it is not compatible, wich...
Hi.
Using 51822 with BLE stack, I was faced with the problem of low transfer rates (5kb) on my android device (phone). It is very slow.
Can work 51822 with standart...
Can I initial like below to generate 2 opposition PWM waves on 2Pins?
/* Configure PPI channel 0 to toggle PWM_OUTPUT_PIN on every Timer 2 COMPARE[0] match. */
NRF_PPI...
Hi All,
Now I'm doing the OTA and I can use the nRF51822 DK and Master Control Pannel to complete the firmware update.I have a idear but I meet some problem.
I use the...