I've modified Nordic's "Nordic_Keyboard" sample to work with my custom board, just simple modifications to use custom_board.h rather than the default PC10028 configuration...
Hi,
I use HID application with S110 v8.0 profil.
I use BLE HID Keyboard example.
I put datas from smartphone to BOOT KEYBOARD OUTPUT REPORT and I whant read them by...
Hi all,
I use nRF51822 module and my environment is Eclipse + GCC + SDK 10.0. I refer to the example in path <SDK_PATH>/examples/ble_peripheral/ble_app_template, then make...
I am using nrf sniffer for trouble shooting. But it always exit unexpectedly. Wireshark was still open but the DOS window got closed.
I am attaching the log.txt.
log...
Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello,
Our device based on nRF51822 with SD110 v.8.0.0.
The firmware use defined area in top of the flash to store some data.
The "RAW" functions sd_flash_write and sd_flash_page_erase...
Hi Team,
Is it possible to scan on one channel and advertise on another channel?
Say node-A will scan on ch-37 and advertise on ch-38 while
node-B will scan on ch-38...
I'm trying to use the NRF51DK to talk to this EEPROM ( www.st.com/.../CD00290537.pdf) . I've started by trying to modify the twi sensor example. One of the things that's different...
I am new to nRF51:
how do I change the softdevice from 110 to 130 in the example project ble_app_uart (and in general) within the Keil µVision IDE.
There is no option...
Hi,
I am developing a product for the 433MHz band. Due to the space constraints I had cut the ground plane to very small and also had to rearrange the components away from...
Hello everyone,
This image was copy from "infocenter.nordicsemi.com".
I'm trying nRF51-DK (IoT SDK) with Coap server , (raspberry pi with Coap client by python example...
Hi,
we are using RTC2 with APP_IRQ_PRIORITY_LOWEST. But the code hanged inside the interrupt handler. when we did step through debug, we came to know that in nrf_drv_common...
In nrf52_SDK/examples/peripherals/rtc we tried adding the UART prints and verified. It was working fine for RTC0 but fails to do for RTC1. Could you please give any hint on...
Hello together..
i have a problem with the nRF51 DK.
I tried a little bit with this DEVkit i.e. copy the blinky example to the JLINK storage.
This works fine.
Regarding...
Hello,
I am developing a new product using S130 on nRF51822(QFAC). My product use LCD as spi interface and ADXL345 sensor as i2c interface, also test it, works well without...
Hi all:
To saving power I implement the function to read data after interrupt is triggered..
below are my codes..
My expectation is..
Let CPU enter idle mode to wait...
I am trying to set up a GPIO interrupt, and found that whenever Button 1 is pressed, if Button 1 or 2 is pressed later, the app will reset. This is even if there is any other...
Hi.
I want to make a device which can connect each others and communicate with NUS.
I need not to use any other service without NUS.
I made nus_c service which is a central...
Hi
I can't seem to find this in the datasheets, what is the active current consumption of the nRF52832 chip, I'm interested in the maximum expected current consumption...
Hi!
I want to connect a nrf51 dk with a beacon and I'm using the UUID to make the connection. In the beacon code I define the UUID in this way:
ble_uuid_t adv_uuids...
