Hi,
Is it possible in BLE channel sounding in ncs 3.0.1 to get some information about the quality of the distance measurement for each method? We have three ways to get...
Hi,
my name is Nick De Leenheer, and i am finishing my thesis on indoor localisation with CHANNEL SOUNDING. i currently got these outputs in my venv using SERIAL: so i...
Hi,
I´m working on a Zigbee-based environment sensor. You can find all related files here: https://github.com/Kampi/BeeLight
Now I have the following scenario: the whole...
Does the nrf54l15 have a register to specify the boot area? Similar to the NRF_UICR->NRFFW of nrf52833.Or does the nrf54l15 have to boot from address 0x00000000?
Hello,
I've been going through the BLE fundamentals course and things are going well. I'm using the nRF5340DK board and SDK version 3.0.2
I've gotten to lesson 3, exercise...
Hi,
I am working on the channel sounding feature on the 54l15 and I want to perform it sequentially between 3 reflectors and one initiator. I realized that after I make...
Hi,
We're at a point in our project where we're working through some regulatory testing for ETSI/FCC certifications with our BLE dongle board (nRF52840 + nRF21540 FEM...
Hi.
I am designing PCB based on NRF51822-QFAA-R7.
There is 2450BM14E0003T balun will be used.
Here is reference design for that pair (NRF51822 + 2450BM14E0003T):
www...
I would like to register a bug report with the nRF5 SDK version 12.2.0. If you look at the example code in the SDK you will find that every example has a different build configuration...
We have a project which need to control the distance between the slave and the master to be less than 10m, say 5m. We tried -20 and found it a little longer than we expected...
How can I trasfer 20bytes data per 10ms?
Currently, I set gap_conn_params.min_conn_interval 7.5ms, and use BLE_EVT_TX_COMPLETE to send data. However, Android APP nrf Connect...
[Aim]
I am working on a project where I aimed to Integrate/Develop firmware management system using Contiki running over Nordic NRF52.
[Components]
Contiki running over...
On a nRF52832...
I'm trying to create a DFU package to update an existing SDK 11 SD2.0.0 firmware, to update it to SDK 12 SD + new application + secure bootloader
But the...
Hi
I am using SDK 12.3.0 with softdevice s130 v2. When I try to combine ble_app_hrs_peripheral code with app_uart.c, uart module gives error NRF_DRV_UART_EVT_ERROR in uart_irq_handler...
I would like to use twenty concurrent connections. As I understand I should set ble_cfg.gap_cfg.role_count_cfg.periph_role_count = 20 and ble_cfg.conn_cfg.params.gap_conn_cfg...
Hello,
I have read with a lot of interest the documentation associated to the "multiprotocol support" associated to the nRF5 SDK for Thread v0.10.0.
As far as I understood...
This is a more specific counterpart to a question I posted on StackExchange . If you want to know more about the attack itself, check that out, but here, I'm asking for a...
Hello, please refer to the below code, in particular, did I get the cccd handle right?
static uint32_t mesh_value_char_add(void)
{
/* BLE GATT metadata */
ble_gatts_attr_md_t...
In order to prevent communication from middle-man attack, I append the signature after ECDH publickey. However, though I get the correct share secret by ECDH, I fail in verifying...
Hi,
I'm using the bluetooth 5.0 and base on the mutilink_center example to add a peripheral and a center. Because I want the center to connect two type device. It could...
