Does the nrf54l15 have a register to specify the boot area? Similar to the NRF_UICR->NRFFW of nrf52833.Or does the nrf54l15 have to boot from address 0x00000000?
Hello,
I've been going through the BLE fundamentals course and things are going well. I'm using the nRF5340DK board and SDK version 3.0.2
I've gotten to lesson 3, exercise...
Hi,
I am working on the channel sounding feature on the 54l15 and I want to perform it sequentially between 3 reflectors and one initiator. I realized that after I make...
Hi,
We're at a point in our project where we're working through some regulatory testing for ETSI/FCC certifications with our BLE dongle board (nRF52840 + nRF21540 FEM...
Hi,
I'm using zephyr RTOS.
I'd like to put the cpu System ON Sleep Mode to conserve power.
Then, I'd like to restart the CPU with an interrupt or event from the comparator...
Dear Staff,
we have some Ublox C2909 TAG based on your nRF52833 chip.We need to program them for an RTLS project.
In particular we need to:
customize the FW here ...
Hello,
I managed to run the examples for nrf54l15 channel_sounding_ras_initiator.c and reflector on my custom hardware boards. I changed the overlay files to use my own...
Hi,
I need to use watchdog as a timer, and I can enter WDT_IRQHandler for now. Can I stop watchdog reset the system in this IRQHandler? So I can counting like a timer.
...
Dear all
is there any possibility to use PC to test the nrf51822, Instead of Android/ios app?
preferably a lib to be used with Java, so one can have some test cases...
I want to sync some information and control code between Nordic and our CPU(ST), so I need to study serialization function. But I only have serialization function sample code...
Hi
I'm going to use a module that uses nRF51422 and that has an adapter to be soldered as a SMD in a circuit to mimic the footprint of an AP2 module. The adapter only has...
I'm implementing my own equivalent of hci_dfu_send_hex;
There is not enough information in the documentation on how these packets are constructed.
I found that the first...
Dear community
I've got this nice "white-blue" Kit, neat toolbox to configure the tag and run it.
Now, for Battery/ImmediateAlert profiles and other parts seems to be...
Hi,
How can i test the proximity application with the use of nexus4 smart phone and nrf51822 evaluation board?
We already tested the ios proximity application which are...
Hi community,
Till now I developed some BLE applications on the TI-controller CC2540, but for my new project, it seems to bee not fast enough. So I'm seaching for an alternative...
Im mainly considerate about ANdroid and iOS devices ,I understand this is also dependent upon profile support over the android and iOS devices but this should not be an issue...
in my pca10001 board,
once i made led pin 18 and 19 pin as internal pull up.
led is not on,and i probe it also but not high.
here my config in blinky example.
...
hello
i have a problem i send from device to host the temperature, but it send the temperarture just one time
and i want that the device should send it every 10 seconds...
Hello
Im new in arduino and i want to connect an rfduino with one other rfduino
how can i send from one rfduino to other the degreee an how can i see the degree on the...
Hi!
I have a problem with testing ble_app_hrs_c. I am using nRF51822 develpment board + nRFgo Motherboard. Softdevice is S120 1.0.0 1alpha, SDK version is 5.10. Specifically...
The article that mentions the S120 and Rezence is this one: www.nordicsemi.com/.../Nordic-Semiconductor-announces-Bluetooth-Smart-solution-for-Rezence-Wireless-Charging-and...
Hello
I am new to developing with the evaluation kit and have a few very basic questions.
Any answers or pointers to relevant documents would be much appreciated.
...
