Greetings!
I am using Wireshark along with an nRF52840 dongle to monitor BLE traffic between a mobile app and connected peripheral and periodically I see some "L2CAP Fragment...
Hello, I am using the nRF54L15 board, and trying to connect to the Adafruit SHARP 400x240 monochrome LCD display .
I got the display driver alone to function just fine after...
Hi,
I am trying to perform a DFU using SMP over BLE. My setup has NSIB and MCUBoot enabled and thus I am able to perform DFU for MCUboot and Application using nrf device...
Hi all,
I'm trying to use uart2 on my custom nrf9151 board, but I'm stuck. As I understand, I use i2c1 so I can't use uart1 and i2c1in parallel, so here is why I wnt to...
Hi - I am seeking clarification on a topic as I am a little unsure on the correct way to do things.
I'm using an nRF52840 and porting an old Firmware from nRF5 SDK to NCS...
Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
Hi, i'm using NRF5191 with DECT.
DECT modem: 1.0.2
App: hello_dect sample
In datasheet I found that NRF9151 support various band: 1,2,4,9,22
and I'm using these value...
hi, I want to use BLUETOOTH for Position Service,
Did nrf52840 or nrf52832 support new feature in BLUETOOTH5?
like (1)LE Extend ADV?(2)LE Periodic Advertising Create sync...
Hi
I would like to write some data to flash directly before powering off. I have a few questions:
What is the best way to know if my write operation has finished...
Hi,
The followings are more like an observation rather than a question..
We just upgraded to SDK 14, and realized that some of the RTT logs were mysteriously disappeared...
Our application is running as a peripheral on a nrf52823 with SD132.
It starts running with slower connection interval (95-100ms) which is what we initialize the stack to...
I write the code without BLE part first, all the function works good but after I add the BLE part, it cause the chip reset. it seems like a random reset. why?
Hello, we would like to release our product to the market.
Our device is a (BLE) beacon based on nrf52 which is advertising some data encoded as manufacturing specific...
Hi everyone!
I have probelem with receice data over UART. In the other MCU use core ARM as : STM32, NXP... when a byte is recieved, MCU has flag to notify. That is "interrupt...
My code is in the link attached:
github.com/.../master
With that code we have a current measurement of 1.1mA. As you can see in the code, we have tried to disable all...
Hello guys, i am Dani.
Actually i am new in hardware communication and i have problem with BLE - Android Pairing.
The details are as follows:
I was trying to perform...
Hello,
As per my requirement I want to develop a device that would be capable of sending & receiving data to & from a web server & at any point of time multiple devices...
Hi everyone,
I am using board PCA10040 v1.1.0, softdevice 13.0.0, Eclipse Oxygen. I am trying to connect my board with a device call Daydream controller .
There is also...
I am seeing this warning flag on almost every files in Keil projects in the nRF51 SDK v10.0.0, be it original unmodified examples or projects that I modified from such examples...
If I want to get 16kHz output sample rate of PDM,then what should I do? How to cofigure the register PDMCLKCTRL and the clock HFCLK? Could you give me more details? An example...
Here are 4 broadcast signal, the first is send with dfu, whenever how I try, it only display 8 characters in max.
And the second and the fourth named begin with "LOCK_...