When my peripheral calls sd_ble_gap_phy_update, setting rx_phys and tx_phys to BLE_GAP_PHY_AUTO, I receive the BLE_GAP_EVT_PHY_UPDATE event with a status of BLE_HCI_UNSUPPORTED_REMOTE_FEATURE...
Hi all,
I recently bought an nrf52840DK, and yesterday I tried to program an external board through the p20 connector on the DK with the SWD pins. I was able to flash the...
Certainly! Here’s a clear, natural English version of your email:
Dear Specialist,
I would like to better understand the two variables used in the SDK for calculating...
Hi, Using NCS 3.0.0 it would appear that the function sntp_simple_helper does not work with SYS_FOREVER_MS as a timeout value.
Problem: When we pass this value as a timeout...
Hi All,
I have a question and slight confusion as referring to couple of links.
Performing KMU provisioning : Here we are highlighting provisioning of private key up...
Hello
I'm trying to use LittleFS with an external SPI flash, but if the SPI flash isn't available yet at boot time, my application hangs for an uncertain amount of time...
Hi, I am currently working on UART sample codes and have 2 nrf5340 Audio DKs . One acts as peripheral and another as Central. i want to modify the central board to connect...
Hello,
My application perform reset periodically. When It does a reset the bootloader need to initialize the softdevice with SD_MBR_COMMAND_INIT_SD before calling sd_softdevice_vector_table_base_set...
Good times,
So I finally put in the tweak to enable the GPIO 9&10 pins to be used for GPIO instead of the default NFC mode. Must remember that reset for it to take effect...
Hello,
I'm testing ble_app_hrs example by nRF52832 DK.
When i change NRF_BLE_GATT_MAX_MTU_SIZE up to 158, the example project run properly.
But, when i change MTU...
Hello, I am using nrf52832 custom board, with SDK 11.0.0 and s132_nrf52_2.0.0 and trying to dim led. It seems the only suggested solution is to use the pwm driver. I was wondering...
Hello, im experimenting around with the nRF52 DK (and nRF51 DK also)
Now I have following setup on nRF52 DK:
SoftDevice: s132 nRF52 v2.0.1
Applicatoin: Example Project...
I have the option to connect nBLE51822 to MCU via SPI, UART or I2C. But is there any advantage of using SPI/ I2C interface over UART interface while connecting nBLE51822 to...
my code is below.
git_mpu9250_dmp.zip
Hello.
I use nRF52 & MPU9250.
I want to use DMP,
but I can't read data with DMP.
Because it have failed that writting firmware...
Hi there,
What is the recommended development tool setup for nRF52 Preview DK on Mac OSX?
Your guide for SDK 0.9.1 seem to rely on Keil which isn't natively available...
Hi all,
What is the difference between the app_mailbox and the nrf_queue api?
The documentation says:
A)
The mailbox library provides functions to safely exchange...
Hi team ,
I'm using sdk 12.1.0(E:\testing\examples\ble_central\ble_app_hrs_c\pca10028\s130) example.I want to change to this BLE_GAP_ADV_TYPE_ADV_NONCONN_IND in above example...
I'm using nRF52 + SDK11.0.0 + s132. I have a custom service (with a read characteristic and a separate notify characteristic). After adding the DFU service and uploading the...
Hi,
Following the docs I think I am able to write to flash but it will not read anything .
This is how I set it up, write and read :
static void sys_evt_dispatch(uint32_t...
Hi,
I used a PCA10040 dev kit with nrf52832 to test Serial Secure DFU Bootloader.
Followed all the steps in the example with my PC (Ubuntu 16.04.1 LTS 64-bit).
I...
I am using SDK 12.2.0 with soft device s132 3.0.0 using NRF52 Development Board(PCA10040).
I want to update Battery level to central device/APP.As i want to use code for...
