i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
When using nrf51-ble-driver_win_0.3.0 with Visual Studio 2010, after I put a breakpoint in my code, when I try to have the process "continue", I always get unandles exception...
I use SDK 9 and nrF51 in the advertising mode. I want to advertise each 1s packets.
First, I call function
set_adv_params(&m_adv_params);
where I
static void set_adv_params...
Hello,
I try to implement the BLE / Cycling Speed and Cadence Service and try to figure out, how to initialize the ble_cscs_init_t data structure. Currently I'm wonder how...
I am building a cadence sensor form the Cycling Speed and Cadence Service module.
Unfortunately the sensor I have built is recognized to have both speed and cadence when...
hi
i flashed s110 softdevice 7.1.0 then ble_app_beacon example application fron sdk 7.1.0 into nrf51822 beacon successfully.but led is not at all blinking in beacon.and i...
Hi
I have got two nRF52840-pdk for long range application design. After reading posts here I realized that the softdevice s140 can only change PHY to CODED after a connection...
Hii guys I am using an nrf51 DK board for my project and I am trying to find the number of advertisements send from the time the board was power up or reset. From my knowledge...
Hi,
I would like to be able to provide a visual indicator such as a blinking LED when the chip is in the Emulated System OFF mode. Note that if the chip is in DEBUG mode...
hi
i tried ble_app_uart from sdk 8.0.0 in pca10028 and it is working.but i want to run it in pca20006.i changed device to 51822 & board to pca20006(in preprocessor settings...
Hi. I'm using nRF52832, SDK13, S312v4 as peripheral.
I want to change connection parameter as below.
#define MIN_CONN_INTERVAL_FAST MSEC_TO_UNITS(30, UNIT_1_25_MS)
...
Where can I find the completed source code for the BLE Services, a beginner's tutorial
I keep having trouble advertising, so either I am missing something, or have incorrect...
Hello,
I used latest port_cmsis_systick.c from SDK13.0. And there is still xTickCount bug. Function vPortSuppressTicksAndSleep() adds correct vTaskStepTick(diff); but the...
I am using nRF52 S132 and latest SDK V11. I defined a custom service with a custom characteristic which is 509 bytes (based on your tutorial). Read operation is fine from...
when a particular line of my code is at line 54, the following compile error occurs:
error: #101: "assert_line_54" has already been declared in the current scope
line...
