Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
Hi,
As well know, the nrf51822 can only work either TX or RX mode at the same time.
Normally, the nrf51822 device is working in RX mode (by using function "nrf_esb_start_rx...
Hello, i'm trying to updade my firmaware using the DFU. I manage to do it with nRF Connect and nrfutil but i'm trying to a custom central to flash the software without any...
Dear all,
I am using an adafruit-nrf52-pro-feather (nrf52832) to run my project of detecting voice by this below scenario:
++ Setting up:
[PC] ==== USB cable ====...
To learn how to use FDS, I started by importing the code from the flash_fds example. My application is using peer manager and I got really strange errors until I realized...
Hello!
I am trying to set up the interface between an ARM Cortex-M4 andthe nRF8001. After RESET I see following data on the MISO line:
(turquoise=REQN/CS - pink=MOSI ...
Hi,
I would like to control the LEDs based on the PTM 215B switch by programming it using nRF52 DK. Where each button in the switch should turn one LED.
I am using...
Hi, Nordic.
I'm developing multiple peripheral and a central. Central is only scanning and Peripherals are only advertising.
I got Adv data and Scan rsp data successfully...
Hi,
I work on a ANT proximity search project using SDK12.2.0 and softdevice S332v2.0.1 on nRF52832.
I have a ANT sensor which is 5cm apart from the Nordic 52832. And the...
Hi there,
Can you please tell if with 'Sniffer' I can track down and see all images shared with my pc's webcam?
If so, how can i do that?
Thank you so much for your...
Hi all,
I am moving from Keil into SES, and one of the things I am not being able to find is how to do the __PACKED pragma.
I see in SES that:
#elif defined ( __GNUC__...
I'm trying to use the SEGGER debugger with one of the OpenThread examples for the nRF52840. When I click on the "Go" button, it asks for the location of the source files for...
I think I found a bug in ble_dfu_bonded.c.
In ble_dfu_buttonless_bootloader_start_prepare() there is a call to gscm_local_database_has_changed(). The problem is that this...
Hi,
How do i enable Gyroscope Support in Smart Remote FW v1.2?
When I enable this in the sr3_config_*.h file, setting "CONFIG_GYRO_ENABLED 1", I get an error stating:...
Hello,
I have moved my project from SES 3.34a to 3.40 and I see a new error at compilation.
When compiling the file nrf_pwr_mgmt.c’, I have the errors below :
unrecognizable...
While attempting to run the following code from a MESH example in IAR, the program gets stuck. It only seems to be calling button_event_handler continuously, as if the interrupt...
