Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
I'd like to use the GATT/GAP driver from an ARM based Linux system. Is there any possibility of getting a library compiled for ARM or (cough) the source code to build it myself...
I downloaded radio_test.c from Nordic and complied it to output a .hex file. Now I want to flash this .hex file onto nRF52832. Does it require to softdevice and bootloader...
Hello (I'm new to this nRF-world...).
I am searching for a small "nRF-52832 clock" (arm mounted watch) that at least reports the "surrounding/room temperature" (not only...
Hello
SDK12.3, nRF51822
Example Gazelle from SDK works fine. If I use the softdevice (add ble_stack_init) then the program freezes in the nrf_gzll_enable
I want to do changes for firmware upgrade nrf52832 with SDK BLE_2.0.1 for the mesh.
I need DFU (Bootloader)UART for our application to upgrade nrf52832 firmware by the host...
Hi
I have written this code based on a sample from SDK12. The board is a pca10040 and nRF52832 chip. It seems like after disconnection from the master device the Softdevice...
Dear support team,
Channel survey (RSSI report for each data channels) are now available on S132v6. However, for users who need to use v4.0.2, is there alternative method...
I am using the Hackable Kit from Electronut labs and using their Bumpy , black magic probe alternative for programming. I would like to control a servo motor precisely at...
My code is on the multi-link example and it works well when I use another nrf52dk board as the "Nordic_Blinky" peripheral device, but it can't find my other BLE device.
...
Hello
I am running gls example on SDK14.2.
I paired after flashing program to my DK board, and then turn off power.
And turned on again, but i can't connect to my DK...
HI. I used a translator.
I am using the RNG example of SKD15.
I know that when I set the range of the random number to 1 byte, the number from 0 to 255 is generated. ...
I am using a Raspberry PI as a 6LoWPAN router, running Raspbian 9.4. Linux 4.14.34. Radvd 2.15.
I configured everything as described in IoT User Guide . I am using Miredo...
Hi,
As well know, the nrf51822 can only work either TX or RX mode at the same time.
Normally, the nrf51822 device is working in RX mode (by using function "nrf_esb_start_rx...
Hello, i'm trying to updade my firmaware using the DFU. I manage to do it with nRF Connect and nrfutil but i'm trying to a custom central to flash the software without any...
Dear all,
I am using an adafruit-nrf52-pro-feather (nrf52832) to run my project of detecting voice by this below scenario:
++ Setting up:
[PC] ==== USB cable ====...
To learn how to use FDS, I started by importing the code from the flash_fds example. My application is using peer manager and I got really strange errors until I realized...
