I was working with IAR and SDK10.0 before. For some reason I have to transfer my project to Keil and SDK9.0. My program worked well for the old settings. While keeps got NRF_ERROR_SOC_NVIC_INTERRUPT_NOT_AVAILABLE...
Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
I'm using nRF52DK and SDK12.2.0.
Trying to change MTU size.
When I modified app_nrf_uart example as below
#define NRF_BLE_MAX_MTU_SIZE 103
Then infinite reboot...
I am working on a project and have successfully implemented single channel PWM to dim leds (using a transistor FET).
The pwm init code is below:
uint32_t err_code;
nrf_drv_pwm_config_t...
image description (http://)when i try to flash the led binky programme to nRF51822 Ek. i am getting device error and LED also glowing continuously.
1.this device error was...
So I was thinking of having the following:
nRF24L01+
to balun (e.g., Johanson 2450BM14A0002 or Anaren BD2425NnRF)
to PA/LNA RFX2401C
to PCB antenna
If...
Hi all,
I want to clarify are there any deference between "connection_id" and "conn_handle" ?
I use a multilink central application with 8 possible peripherals devices...
Hello,
I have some difficulties to make an ant acknoledgement with my nrf51422 (s210), and i would be grateful if you could help me with it. (SDK used 12.2)
I have 2...
Please give me info about configuring a timer at given timeout. For eg,. if we want to blink LED for 30 seconds, how to configure them using timer events.
What is the optimum reset strategy for Debugging the nRF52832 with a Segger J-Link Plus?
(Setting of Project_Options/Category:J-Link_J-Trace/Reset)
nRF shall not...
Hi,
I am using SD 120 Ver 2.1.0 and SDK 8. I am getting disconnection with reason 0x3E sometimes. After disconnection even master is scanning, It wont get connected with...
I've been working on a separate problem with the NFC Type 4 library when I ran across this. I can duplicate it in the experimental_writeable_ndef_msg example.
All I did...
Hi Nordic Forum!
I've been trying to run a test program (pin toggle) on a custom nRF52832 board.
First, I tried the same program on the HDK to toggle pin P0.17 (LED1...
When I use additional VS UUID, should I use sd_ble_uuid_vs_add(), se_ble_gatts_service_add() in order?
example,
sd_ble_uuid_vs_add(); <- VS1 UUID
se_ble_gatts_service_add...
