Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
I have been trying for a few days now to get my environment setup for development with the nRF51822. Since there is no official configuration for the Mac w/ Eclipse I have...
Here: email.1and1.co.uk/.../Part_1.html
Bluetooth low energy (formerly Bluetooth Smart)
Shouldn't that be the other way round; ie " Bluetooth Smart (formerly Bluetooth...
hi, i gonna make a single wireless communication between nRF51822 chip and smartphone(nRF Toolbox) .
i can download some refernece layout of nRF51822 chip but there isn...
To adding more 128 bit UUIDs, more services, and more characteristic.
vs_uuid_count is the number of 128 bit UUIDs.
But I figured out the attr_tab_size only by increasing...
Hi there!
I want to send a float from nRF51822 to MCP App. I use this code:
float m_temperature = 26.3f;
uint8_array_t temperature_data_array;
temperature_data_array...
Hi everyone,
I was wondering if there are any issues turning on and off the ANT transmitting channel during run-time of nRF51422 with this:
err_code = sd_ant_channel_close...
I want to use master spi mode ,but when I build the file,it is always error.I operate like this ,First I open the project in ble_peripheral\ble_app_hrs\pca10040\s132\arm5_no_packs...
"Hi Guys, my nRF8001 BLE is working perfectly, But recently i was performing regression testing to check BLE connection, their i faced one issue after 10 minutes from nRF8001...
I am using SDK11 on a nRF52 board. I had some success in DFU, but also had issues.
Was able to upload the bootloader successfully using Master control panel. But it always...
I use the nRF52832 IC of WLCSP package.
In addition, it sets as follows:
{.source = NRF_CLOCK_LF_SRC_RC, \
.rc_ctiv = 16, \
.rc_temp_ctiv = 2, \
.xtal_accuracy...
Hi all,
I have a firmware in which I want to use BLE and ANT communication (with Softdevice S310) to send and receive commands from other Nordic devices or smartphones...
Hi,
I modified the code from the tutorial at devzone.nordicsemi.com/.../ to send measurements from my RHT sensor but encountered some basic difficulties. After fitting...
Hi,
I would like to know what the approximate Flash memory and RAM usage by nRF51 chipset would be when using the BLE communication (Let's say I want to send and receive...
Hi everyone
I am working with nRF52 (SD132). I am considering the ble_app_uart example and I'm trying to modify it by setting TIMER1 and TIMER2 peripherals to generate...
I'm trying to update the bootloader over the air, I succeeded to do so following the answer given here
it worked when I didn't change big things in the bootloader , but...
