Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi, I am unable to build this example in Keil Uvision5. I am getting following error:
"no source": Error: #5: cannot open source input file "......\main.c": No such file...
Hi,
I am trying to setup a testing environment using nrf51-ble-driver_win_0.5.0.
All of my job are:
Download nrf51-ble-driver_win_0.5.0, and program connectivity_115k2_with_s130_1...
Recently updated to SDK11 + s130 v2.0.1 on an nRF51822 xxAC LFCLKSRC=RC
BLE Advertising no longer works. Localized it to our use of TIMER2 for an implementation of systick...
Hi,
Im trying to connect MCP25625 via SPI on nrf52. I checked with the scope that CS, MOSI and SCK are correct, but I get no reply on MISO line whatsoever.
I perform a...
Every time I want to connect to Nordic ble device from my Phone, it ask for pairing confirmation and then it create bond. That's how it should be.
But if the device is...
I'm using nfr52 with softdevice s132.
I want quickly perform flash write during power loss.
When I realize write using fs_store() I obtain time more than 5 msec.
How can...
Just do
NRF_POWER->SYSTEMOFF = 1;
in main()
and found if it's boot by powerup
the current is 10.4uA~10.5uA
and if a re-flash the hex, the current is 1.4~1.5uA
...
Hi,
Everyone,
I am using NRF51422 chip for my custom board. with transmission interval set to 2000ms and Tx power to -20 dBm, I transmit 32 Bytes BLE data and Scan and...
I use the softdevice which is s130.The code is from the demo:
static void nus_data_handler(ble_nus_t * p_nus, uint8_t * p_data, uint16_t length)
{
for (uint32_t i =...
Hi,
i'm using SPI to transfer data divided into packets of 24 bit from NRF51 to a DAC. The function that allows to send data is:
spi_master_send_recv(SPI_MASTER_1, data_vector_tx...
I'm having trouble starting my application after power cycling after flashing it with the DFU app.
I started nRFgo Studio. Erased the chip. Programmed the SoftDevice (s130_nrf51_2...
I was just wondering if anyone has any experience with or thoughs about using Zephyr ( www.zephyrproject.org/) or Mynewt ( http://mynewt.apache.org/) that they would like...
Hello all,
i am struggling with the example code of the Enhanced ShockBurst Protocoll in SDK 11. I cannot really see the structure of the code, to which time which event...
Hi all, in the forum I can read about people having issues with wrong CRC in the bootloader, but with SDK11; I have the opposite problem. It is always 0 and is always accepted...
