Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
I'd like to use the GATT/GAP driver from an ARM based Linux system. Is there any possibility of getting a library compiled for ARM or (cough) the source code to build it myself...
Hi guys,
I am developing a project where I have a large group of NRF52 chips together in one room. In their normal state each chip is paired as a BLE peripheral device...
We are working on a NRF52 DK. In the data sheet of NRF52832, there is no mention of enhanced shock burst mode or dynamic payload or multiceiver. Do I need to refer additional...
we're using Mbed for NRF51822. our board using 2 GPIOs interrupt.
problem: the Rise edge did not generate the Interrupt event: set EVENTS_PORT.
I try uisng while, but...
Hello,
I will explain my setup:
I have 2 nRF51-DK each one of them connected via I2C and SPI to two different custom boards. One being the central(nrfA) and the other...
Setup: DK #1 is running native S110/SDK10/nRF51, one service 128-bit w/ 16-bit char:
Service UUID: 0x0xb1ad
Service UUID type: 0x0x2
Service handle: 0x0x0c
Service handle...
I found a discrepancy between a tutorial and an application note.
Step 2.A of "BLE Characteristics, a beginner's tutorial" devzone.nordicsemi.com/.../ calls sd_ble_uuid_vs_add...
Hi,
I tried to familiarise with eclipse environment and i have some problems :
The debug and run button. I searched on google but i didnt found anwser.
How can i define...
I find example : nRF51_SDK_7.0.0_2ab6a52\examples\properitary_rf\esb\esb_ptx_prx .
question 1: can i add this example into my project that build on SDK v610 and it run...
Hello,
I have an problem with DFU on nRF 52 I have followed this thread devzone.nordicsemi.com/.../ but failing to upload firmware.
I have attached screen shot. You...
Hi
I have noticed that the moment I start SAADC task ("nrf_saadc_task_trigger(NRF_SAADC_TASK_START);"), my CPU current consumption rises by 2 mA!
(tested with chip version...
Hello..
I am Using The Balun having Digikey Part No.2450BM14E0003T And Antenna Part No is . 2450AT18B100E
Then it it is Necessary to add Pi network for matching antenna...
I am working on a school project using the NRF51822 with SoftDevice 130 on a custom board and I aim to create an HID gamepad. I am working on my power supply circuit and my...
Hi,
I just got a nrf52832 pca10040 board and I downloaded the last SDK nRF5 v11.
I downloaded Keil uVision5 and was able to load some examples and test them: nfc record_url...
