But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello everyone
I'm trying to disable advertising but it doesn't work in some cases, I don't really know why. Here is my pretty simple piece of code:
/* Disconnect and...
www.keil.com/.../uv4_db_dbg_evr.htm
www.keil.com/.../EventRecorder.html
Keil worked in a new EventRecorder feature that uses some SWD buffer memory to push data out...
Hello,
A question to understand please. A lot of issues still unfixed in rev 1, but are known for a long time (see errata docs). Like SPI with RX = 1, DCDC -4dB on RF,...
Hello, I try to run the sdk example for adc, i set an input voltage in varying from 0 to 4.38 V in the pin 4 (AIN2), but the returned value didn't corresponds to the desired...
It there a specification for current draw during POR? (From time Vdd starts rising until cpu starts executing?) For nRF51 and 52.
I found this devzone.nordicsemi.com/....
(Hello! I'm drawing the module circuit base on nrf52832 with rfx2401 power amplifier (PA). As I understand it needs to set pins TXEN, RXEN to high level to activate this PA...
It may sound a bit old and you may have fixed them in latest Soft Device stacks however I wanted to share with you a couple of pairing issues we encountered with Soft Device...
i am using nrf52832 and programmed it with eclipse by blinky example.. now i have to debug the project , but when i debug the project with the configuration given in tutorial...
Hi,
We are using a BL652 from Laird, embedding a nRF52832. We wanted to give Zephyr a try, but we are facing a problem.
We compiled the blink example, but when we flash...
Hello dear Nordic members,
I got a theoretical question: I want to connect two chips, one as central and the other as peripheral. Is it possible to stop advertising procedures...
I am using nrf51822 for a BLE project as peripheral role. I am using S110 soft device (SDK version 10).
I want to store bonding information, GATT data and all data storage...
Hi ,
I am working interfacing SD card with nrf52 using fatfs example given in SDK 12.0.0. While writing to text file created in root directory, code gets stopped as size...
Hi - I am designing some boards using the NRF52832 and would like to check a couple of things about footprint design. Unfortunately I don't have access to Altium, and am therefore...
Hello,
I did a code that does scatternets with nRF52 (in connected mode) but it's very dirty because i collected informations all over forum during months and project was...
Dear Nordic Support Team,
In a recent news received by email regarding a new version of "nRF5x Command line tools v9.2.1", it is written that Nordic does not recommend...
