Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
Hello, I have nRF51822 Beacon Kit (pca200006). I'd like to upload .hex file in DFU over ipad, I picked beacon example from sdk 11. When I point on the hex file from ipad toolbox...
Hello,
I am running the NFC example applicaiotn(URI Message Example) in SDK5 v11.0.0. I am using a PCA10040(V1.1.1) dev board with the NFC antenna connected to it and testing...
We would like to use the nRF52 for an indoor application that should cover a a single family home.
The requirements for throughput are very relaxed, so we'd like to trade...
Hi Nordic,
I am trying to figure out the relation between a certain page number (say, 0xFE) and the group of addresses that it contains. How can I get this relation?
...
hi,
I am working with nr52832 and SDK 12.1.
I have referred the RNG example based on which I have integrated that code section in my custom application:
rng_generate...
I'm trying to accomplish a communication from the nrf24LE1 to the nrf24L01+. The nrf24L01+ is hooked up to an Arduino UNO. The nrf24LE1 is flashed with the "enhanced_shockburst_ptx_nrf24le1...
6.1.4 Erasing a page in code region 1
When erase is enabled, the NVM can be erased page by page using the ERASEPAGE register or the ERASEPCR1
register. After erasing a NVM...
Hello,
I was testing BLE Heart Rate Collector Example with two nRF52832 devices, one was programmed with ble_app_hrs_c as a BLE central role, and the other was programmed...
Hello everyone,
I have very pesky bug that is leaving me in fits. I have a feeling it is a timing issue, but I am not sure at this point. Here is my issue, and I would...
Hi Devzone.
I've taken the ble_app_hrs example,
and then added the example code from the PWM Driver example.
The PWM module is mostly functional,
however I have a...
Hi,
I'm trying to build a SPI Slave <-> BLE bridge, so that everything received over SPI bus is forwarded on BLE and vice versa. In order for the reverse direction to work...
Hello,
i think this is simple question, but nowhere i can find answer. Is nRF52840 preview development kit (PCA10056) contains built in nrf52840 microcontroller or i need...
I am going through the BLE Central tutorial and am a bit confused by the APPL_LOG function calls, from what I could understand it should give messages on serial port, like...
Hello, I have nRF51822 Beacon Kit (pca200006) and nrf51 dk board (pca100028)
I had an impression I could flash beacon and upload new files using nrf51 dk board as jlink over...
