Hi community,
I have a similar custom board as Thingy53, which has the nrf21540 module on board.
my purpose is to turn on the nrf21540 and do the reconnection, when...
Hi!
With the release of NCS 3.0.1, the required SEGGER JLink version to v8.18. pynrfjrprog is bundled with SEGGER JLink v7.94. From your website, it seems nrfjprog, being...
Hello,
Over the past three days (up until today), we've observed inaccurate behavior in the Message Routing Service. Specifically, we shut down our destination service during...
Hi,
I use the nRF54L15-DK flash fimware (.hex) with "nRF Connect for Desktop - Programmer" success.
And I view the schematic, discovered the DK board have flash memory...
I have a NRF9160 design with a TPS63031 regulator providing 3.3v. When my battery gets weak I am seeing spontaneous reboots, likely due to input voltage droop.
I'm experimenting...
Hi,
currently trying to boot up mcuboot with nrf54l15 pm_static for both cpuapp and cpuapp_ns. Both files are included in the zip file.
I have already tried several configuartions...
Hi,
I'm using nRF9160DK with SDKs v3.0.0
I am trying to use A-GPS with nRFCloud REST. I used the location example and it works correctly. The documentation states that...
With the SDK_11 s130 ble_app_gls on nRF51-dk, i am able to pair and bond with the board with Android 6.0 as central. But if the user forget the paired device on the android...
Good morning,
would it be possible for a Nordic RF specialist to review our antenna design? Preferably we would upload our Altium-based layout for your review.
Thank...
I want to connect a beacon to my android app and I want to know how to make a development environment (I am using eclipse). Can you show me show examples ?? where can i get...
Hello,
the FDS_VIRTUAL_PAGES is set to 3 in all examples which use the Peer Manager module. The parameter's comment says
Number of virtual flash pages to use. One...
Hello,
I am completely new and I am having NRF52 series.
I would like to know is there an ready example for android or iOS phone using Bluetooth:
Control volume...
I programmed my nrf51822 with one the hex sample files that are existed in the nordic package. toolbox app can find my beacons but cannot connect to them and with nrf connect...
Hi all
The nRF51822 product specification V3.2, chapter 8.8, specifies the times t_CSD and t_CC of the SPI slave peripheral for the low power mode and for the constant...
I've experienced some struggles programming for Taiyo Yuden's EYAGJNZXX board. According to the user manual provided its chip is nrf51822 (which supposedly works with s210...
Hello.
I have a question.
I use nrf52 & Keil.
I want to get data from sensors and send it with BLE.
Now, I found sample codes.
It uses UART and sends with BLE.
...
HI,
I want to send an "Echo" command to the nRF8001 using an ATMEGA328. Can some one suggest code for it ? How should the command be coded in a packet ?
Regards
Hey,
currently I use nrf_gpio_pins_set() and and nrf_gpio_pins_clear() from nrf_gpio.h to set and clear specific GPIO ports, respectively. If I want to change the current...
Alright, I have searched high and low and been unable to find a simple answer to this question. It must be possible for the nrf51 to launch Siri on an iPhone, I have seen...
Hi!
I'm doing an Arduino .txt file sending project using the nRF24L01+. But i'm quite a noob in this so i'd like a bit of advice.
I'm using an Arduino Uno, and I made...
Hello,
while reading some nrf5 examples, I've stumbled over a pattern in the examples, where the result code of a function is stored in variable (most of the time named err_code...
