Hello,
We have the custom board with nRF54H20. The VDD_EXT pin is used to power some GPIO ports of nRF54H20 (P1/P2/P7).
The voltage we see on VDD_EXT is about 1.3V instead...
Hi,
I want to test the behavior of Enhanced Multi-Admin added in Matter 1.4.
Is it possible to verify this behavior using a Nordic DK board, sample code and a Raspberrypi...
I've been able to flash consistently but I finally got my nrf5340 custom board working using Hight Voltage DC/DC by setting it to UICR_VREGHVOUT_VREGHVOUT_3V0, but when I...
Hi,
I had a working project for nrf Connect NCS 3.0. I don't know what happened, but now I can't even create a new build configuration. Every time I click on "add build...
Hello,
Please forgive me for this question. I am an extreme noob. And am trying to get started with my first project.
I am working with the nRF52840 DK, and I am trying...
Hi,
I am trying to make the nrf52833 into an Auracast broadcast receiver (for a broadcast from my phone).
I am using bindings to the softdevice controller ( https://github...
Hi Nordic team,
I tried to view logs from my custom nRF54L15-based MCU using J-Link RTT Viewer, but it's (printk) not working. The same prj.conf configuration was previously...
Folks,
Newbie here with mbed, using nRF51-DK, but old hand with nRF51822, S110, SDK, J-Link, Keil MDK, etc. Trying to figure out how the mbed SDK API maps down onto the...
I have 25Q64 SPI flash chip connected to SPI bus. Unfortunately it works too slow even with using IRQ routine via SPI0_TWI0_IRQHandler (everything done like in example spi_master...
I was wondering if its possible to do a "Create new user" function, so the new bonded devices are accepted only if the first connected master tells the peripheral to.
For...
Hello,
I have taken the ble_app_beacon example and added a few things... I am looking to do something very simple like light up an LED on connection. So i added the on_ble_evt...
When is the S130 going from alpha to beta or release?
I understand that what ever answer is subject to change...just hoping to get a "ball park" date/plan.
hello,
I recently purchased a NRF51 dongle and NRF51 DK. I was working with older version of NRF51 development kit. I did n't get any information in the user guide provided...
Hi,
I am using NRF51822 BLE. I wanted to know that when we put this BLE ic in sleep mode then, is there VDD_PA voltage is still 1.6V or it becomes shut off internally.??...
Is it possible to generate useful documentation from the provided .dox file ?
If I run doxygen.exe ble_api.dox I get some Latex and HTML output but looks incomplete because...
What would be the best way to go about sampling and transmitting a signal at 60 Hz? I am considering setting up notifications and a characteristic, but I don't think that...
Mac OS X 10.10 Yosemite rejects the format of the file system and puts it in a read only mode.
This issue was raised last October 24, 2014 at https://github.com/mbedmicro...
Hey guys,
Sorry to a basic question here, but it's been a few hours and I still can't get a connection to either of two brand new nRF51 dev boards, trying both on WindowsXP...
Hi Sir,
I’m working in an application with the demo board A to communicate via Bluetooth to the demo board B and send data between them. In the module I have to do send a...
I have a 51822-DK board. I have followed all of the instructions to set up the environment. Loaded all NRF tools, Keil v 5, install SDK. I began working on the examples. I...
Hello.
I need to hold 64-bit timer value. I store the 32-bit hardware timer value in one variable (low DWORD) and use an additional uint32_t variable as a an upper part of...
