Hi Nordic team,
I tried to view logs from my custom nRF54L15-based MCU using J-Link RTT Viewer, but it's (printk) not working. The same prj.conf configuration was previously...
Hello Nordic Support Team,
I am working on an nRF52-based project on a custom PCB using the E73-2G4M08S1C devboard ( https://www.cdebyte.com/products/E73-2G4M08S1C ).
...
Hi there!
We're designing a system with ~1000 battery-powered moveable devices distributed across a large rectangular area (approx 200m x 1000m) . Each device collects approximately...
I have DevKit board PCA10156 0.9.2. I only see HW files for 0.9.1 on the Dev Kit main page: https://www.nordicsemi.com/Products/Development-hardware/nRF54L15-DK/Hardware-files...
Hi everyone,
I’ve been using the Power Profiler Kit II (PPK2) and was wondering if the firmware source code is publicly available, or if there are any plans to publish it...
Hi everyone,
I'm trying to get the LIS2DH12 sensor sample working with the nRF54L15-DK , but I'm running into an issue where the device doesn't seem to initialize properly...
Hello everyone,
I’m working on a project using two nRF5340-DK boards to measure throughput and RSSI while dynamically changing the PHY and TX power. I started from the official...
I am a student and very new with your product and how to use it.
I just order nRF52840-PDK today via online electronic store.
Please provide complete equipment list...
Hi, I want to OOB pair two equal devices (pca10040 + NFC shield) via NFC. Since its not clear which of the two devices will act as NFC initiator (active) or tag (passive)...
Hi.
I'm trying to upgrade multiactivity_beacon scanner example to SDK 11.
But, there's no config for nrf52(pca10040) in that example.
So, I configured it myself and...
Hello,
I just purchased this device:
www.aliexpress.com/.../32399375500.html
but found out that evaluation board is only a debugger and does not actually program the...
S130, SDK 12.3, ble_app_hrs_c example.
I want to use whitelist function in this example but I can't finish it.
When I run peer_list_get(), it gets all 0xFF, means that...
While investigating connection parameter handling, I noticed the following:
The is_conn_params_ok(ble_gap_conn_params_t * p_conn_params) function in ble_comm_params.c only...
Hello,
I am working with S132 3.1.0 on a project based on FreeRTOS. Under some circunstances I set manually the value of some characteristics by using the function sd_ble_gatts_value_set...
Hi,
I am working with a nRF51822 board and I want to program in OTA. I know how to program over the air, but the only problem is that when I have a new unused board I need...
Hi,
I am adding BLE functionality to one of my existing product. I product will play the central role for which I am thinking to use nRF51822 based module.
I learned...
Hello i read RSSI in beacon_evt_handler() hrs_scanner project:
printf("RSSI: %d\n\n\n",p_evt->rcv_adv_packet.adv_data.rssi);
but he show me a wrong value of RSSI: 4539...
Hello, I connected, according to official layout design, a 32 Mhz crystal to my nrf52840. Using a 60 Mhz oscilliscope, I decided that the crystal isn't working (no sine wave...
Hi all,
I'm on 10.11.1 (El Capitan), followed the instructions here
github.com/.../pc-nrfutil
And it looks like installed was happy but when I try and run nrfutil...
