Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
Hi,
I'm using nRF52832 on SDK V12.2. I add the connection params in the conn_params_init:
static void conn_params_init(void){
uint32_t err_code;
ble_conn_params_init_t...
S130, SDK 12.3, ble_app_hrs_c example.
I want to use whitelist function in this example but I can't finish it.
When I run peer_list_get(), it gets all 0xFF, means that...
Hi all,
I have some problems with GPIO Interrupts.
I'm using nrf52832, s132 and sdk 12.2
The error is totally random so I don't know why is generated. The case is...
Hi,
We are using the Secure DFU from SDK 12.2, with SD132 3.1.0, on a PCA10040.
As a DFU controller, we use a PCA10031 with a SD130 2.0.1 and a project derived from the...
Hello,
We are migrating from IAR 760 to IAR 8.10 compiler does not produce the same assembly for the SDK12 inline function nrf_delay_us.
The original C Function is :
...
Hi, i am working on RTLS project. In beacons i want to enable DFU service using SDK 13.0. But I could'nt find a gothrough process to do the same. Please give me some link...
I am using S132 4.0.2 and SDK 13, and I have theese questions:
I have an application where BLE node establishes multiple concurrent connections (several as central...
Hello,
I'm having systematically an HardFault interrupt ~10 seconds after calling sd_soft_device_enable(NULL, &fault_handler);
This occurs on my bootloader code, but...
Hallo Community,
I am doing the example ble_app_uart using Eclipse, a SDK 13.00 and a board 10040, When i compile the main file I´ve problems with scan params:
#if ...
#define UART_TX_BUF_SIZE 1024
#define UART_RX_BUF_SIZE 1024
Why to send and receive buffer length of the definition of 1024 bytes, increase the value, again if serial port...
Hi, I just bought the PCA10031 nRF51422 based USB dongle and PCA10028 nRF51422 based development board.
The difference between nRF51822 and nRF51422 was the ANT protocol...
Can I use below code to send data packets continuously over nus (>20 packets)
i=UserUart.RxBuf[1]+2;
index = 0;
while(i>0)
{
if(i>20)
{
while((err_code = ble_nus_string_send...
Hi,
I am using nRF52 chip with SDK13.0. MTU size 155.
I am connect with device using android phone. After sending 1 byte command device starting to send continuous notification...
hello there i think i need two uart in my application. i read datasheet of both nrf51 and nrf52
in both there is only one uart.
can anyone have implemented software uart...
Use this routine E:\nordic\nRF5_SDK_12.2.0_f012efa3\examples\proprietary_rf\gzll\experimental\gzp_desktop_emulator
To modify the can communicate with PC nrf24luep pairing...
Hi.
I'm troubled.
I use nRF52 preview DK v0.9.0 & Keil5.
i tried ble_app_hrs_c in example folder of nRF52_SDK.
This program stopped at
err_code = sd_softdevice_enable...
Hello all,
I am actually implementing an SPI-master driver in non blocking mode, I write the following code, when I use a debeug led, the program enters well in the IRQ...
